« previous next »
Pages: [1]   Go Down

Author Topic: Rechambering  (Read 976 times)

0 Members and 1 Guest are viewing this topic.

Offline blpenn66502

  • Trade Count: (17)
  • Avid Poster
  • **
  • Posts: 176
Rechambering
« on: January 14, 2008, 02:40:19 PM »
Does anyone have any recommendations on who to go to for rechambering?

I've decided I'd like a Handi in 357 Herrett and rechambering a Handi 357 magnum
barrel looks like it would be an easy route with the only other requirement of a
30-30 extractor to make it all work.

Since I already reload for it in a 10" contender, dies and such aren't an issue.

Thx,
Brian 
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Rechambering
« Reply #1 on: January 14, 2008, 04:33:03 PM »
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline gruvco

  • Trade Count: (1)
  • Member
  • *
  • Posts: 44
  • Gender: Male
Re: Rechambering
« Reply #2 on: January 14, 2008, 05:31:55 PM »
I know this answer is posted here somewhere but.....is the 357 mag a .357d. or .358d.  bore?  I know shooting a 357d. bullet  in a 358d. bore  will work with success, but what about the reverse?  is accuracy or pressure a problem this way.  thanks--jim
Logged
life is to short to hunt with an ugly gun

Offline WILD_WEASEL

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 207
Re: Rechambering
« Reply #3 on: January 15, 2008, 07:14:56 AM »
What do you think of re-chambering a .357 barrel to 35 Remington?
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Rechambering
« Reply #4 on: January 15, 2008, 07:19:59 AM »
I think it's a great idea since I already did it a couple years ago, had my 357Maxi barrel rechambered,  MSP Ret just had one done not too long ago also. ;)

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline MSP Ret

  • GBO Supporter
  • Trade Count: (173)
  • Senior Member
  • *****
  • Posts: 8940
  • Gender: Male
Re: Rechambering
« Reply #5 on: January 15, 2008, 08:46:29 AM »
Tim is correct, both he and I have had it done. My .336 Marlin in .35 Remington is a great deer gun in the Northeast and works all out of proportion to what the ballistics on paper say it should. The .35 Remington is a great and inherently accurate cartridge. In a Handi it is an outstanding hunting combination....<><....:)
Logged
"Giving up your gun to someone else on demand is called surrender. It means that you have given up your ability to protect yourself to a power that is greater than you." - David Yeagley

Offline WILD_WEASEL

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 207
Re: Rechambering
« Reply #6 on: January 15, 2008, 11:08:32 AM »
Hummmmmmm,
Looks like my BC Carbine may be off the the factory again for a second 357 barrel to re-chamber.  Are there any other parts I need to order and who can do the work?  My 12ga barrel is going to be off for a Poly Choke too.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Rechambering
« Reply #7 on: January 15, 2008, 11:15:41 AM »
Ours were done on ejector barrels, you'll get an extractor barrel, you'll need a .30-06 extractor part #R03686 from H&R, should be straight forward and not as much work as an ejector, see the rechambering thread I posted earlier for sources, Wayne York did MSP's and mine.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline revbc

  • GBO Supporter
  • Trade Count: (94)
  • Senior Member
  • *****
  • Posts: 1156
  • Gender: Male
    • NewLife Worship Center
Re: Rechambering
« Reply #8 on: January 15, 2008, 04:14:59 PM »
Anyone rechamber to 358 winchester, not magnum.  Would a 357 barrel work with a 308 extractor?
Logged
Pastor, NewLife Worship Center
(Retired) Automotive Technology Instructor, West Feliciana High School
Avid Shooter, Hunter, Fisherman and owner of Handi Rifles

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Rechambering
« Reply #9 on: January 15, 2008, 04:27:19 PM »
No one has done it that I'm aware of, MtJerry is wanting to do one, but he hasn't posted on it for a while.

Tim

http://www.gboreloaded.com/forums/index.php/topic,129960.msg1098477681.html#msg1098477681
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline blpenn66502

  • Trade Count: (17)
  • Avid Poster
  • **
  • Posts: 176
Re: Rechambering
« Reply #10 on: January 15, 2008, 05:23:25 PM »
Thanks for all the info.  I wasn't aware that H&R would also sell parts such
as the extractor so I'll make sure I ask for a 30-30 extractor when I put in
my order.

Best, Brian
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Rechambering
« Reply #11 on: January 15, 2008, 08:52:35 PM »
All the part numbers are listed at the bottom of the Handi owner's manual.

Tim

http://www.hr1871.com/documents/manuals/HR_NEF_HANDI_RIFLE_MANUAL.pdf
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Smokin Joe

  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 1230
Re: Rechambering
« Reply #12 on: January 16, 2008, 04:13:04 AM »
revbc, re: the .358 Winchester, I rechambered an ejector barrel to .356 Win ( .358 with a rim ) and it works just fine.
Logged
Deo duce, ferro comitante
With God as my leader and my sword as my companion
Pages: [1]   Go Up
« previous next »