« previous next »
Pages: [1]   Go Down

Author Topic: BC 45/70  (Read 518 times)

0 Members and 2 Guests are viewing this topic.

Offline jack19512

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 639
BC 45/70
« on: October 05, 2006, 04:18:21 PM »
Anyone know where to purchase a scope Mount for this rifle other than H&R?  Thanks
Logged

Offline stimpylu32

  • Moderators
  • Trade Count: (67)
  • Senior Member
  • *****
  • Posts: 6062
  • Gender: Male
Re: BC 45/70
« Reply #1 on: October 05, 2006, 04:27:23 PM »
jack

a weaver # 82 will fit  , it does not have as many ring slots but it will work , i have one on my 45/70 handi.there is a pic in the FAQs

stimpy
Logged
Deceased June 17, 2015


:D If i can,t stop it with 6 it can,t be stopped

Offline DPRinks

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 166
Re: BC 45/70
« Reply #2 on: October 05, 2006, 04:43:32 PM »
And if the Weaver mount does not have a slot where you need it, a couple minutes with a hack saw and narrow file will take care of  the problem.
Logged
D. Rinks

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: BC 45/70
« Reply #3 on: October 05, 2006, 06:00:42 PM »
The worst thing about the Weaver #82 rail is there's no mounting position on the rear 1½" of the rail, so the scope has to be so far forward. I'd give H&R a call on their toll free line and order one, it would be well worth the wait. ;) The rail is $13.50 without a hammer ext, or $18 with the ext.

Tim

http://www.graybeardoutdoors.com/smf/index.php/topic,82422.0.html
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline jack19512

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 639
Re: BC 45/70
« Reply #4 on: October 05, 2006, 07:06:02 PM »
Well, I lucked out.  I remembered having a mount similar to the one used on these rifles put away with a lot of my other forgotten about firearm bits and pieces.

I didn't have two screw mount holes that lined up so with the aid of a dial caliper and drill press that wasn't a problem.

Also the mount didn't have the exact fit on the bottom as my barrel so some sandpaper and a little lapping fixed that.

It is kind of a god awful looking setup but I really just needed a scope so I can make my reloads for this rifle as accurate as I can as my eyes just aren't up to this task very well at distances of 100 + yards with open sights. 

The only rings I had on hand that would work were the very high rings and the only scope I had on hand was a Simmons 6X24X50.  I don't know how long the scope will hold up under the recoil of the 45/70 but I hope to find out tomorrow.

I really wanted this setup for tomorrow that is why I wanted the info on other possible sources for the mount.  I remember a while back that my Walmart had some of these bases on clearance and if they haven't sold them yet I think I will buy me some for future use if the need arises.  Who knows, if I take a liking to a scope being on this rifle I might just get the right rings and a good low power scope for it.  Thanks to everyone for their replies.  :)



Logged
Pages: [1]   Go Up
« previous next »