Author Topic: 32 cal bullets?  (Read 1404 times)

0 Members and 1 Guest are viewing this topic.

Offline 1Longbow

  • Trade Count: (2)
  • Member
  • *
  • Posts: 98
32 cal bullets?
« on: November 13, 2006, 12:55:29 PM »
Anybody here cast 32 cal. round nose bullets ? I'm having a heck of a time trying to find some for a 32 cal. remington pump. flat nose bullets just will not feed . somthing in the 170 grain range---thanks 1Longbow

Offline jhalcott

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1869
Re: 32 cal bullets?
« Reply #1 on: November 13, 2006, 02:13:00 PM »
  have you tried Midway or Mountain Molds? Maybe a check on "cast Boolits might get you somwe help.Are you loading for a .32 Remington? I have NEVER seen one of those !not even a case. Must be a LOT like the .35 Rem.

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: 32 cal bullets?
« Reply #2 on: November 14, 2006, 05:15:00 AM »
You might look at 8mm moulds.  Might have to put up with a gascheck rebate

Offline tacshooter

  • Trade Count: (0)
  • Member
  • *
  • Posts: 72
Re: 32 cal bullets?
« Reply #3 on: November 14, 2006, 06:35:54 PM »
I think I might have a mould that will be good medicine for you. I'll look.

Tacshooter
NRA Life Member
NRA Practical Pistol Instructor
Law Enforcement Firearms Instructor
Proud Father of a Decorated Combat Soldier who fought in Iraq!
PRAY FOR OUR TROOPS IN IRAQ/AFGHANISTAN!

I CAN ONLY HIT WHAT I SEE IN MY CROSSHAIRS.... :sniper:

Offline 1Longbow

  • Trade Count: (2)
  • Member
  • *
  • Posts: 98
Re: 32 cal bullets?
« Reply #4 on: November 15, 2006, 09:16:18 AM »
Thank you for your replies,the 32 Remington is more or less a 32 Winchester without the rimmed case. The 32 Rem. bullet is listed at .321 diameter,the 8mm is listed at 323,issible to shoot this? Sorry if this is a dumb question---1Longbow

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: 32 cal bullets?
« Reply #5 on: November 15, 2006, 05:17:46 PM »
Generally, the less sizing the better.  There are good .32 moulds available from lyman or RCBS.  You suggested round nose.  That means sizing 'em down or look around some of the other mould makers.  To answer your question, lead bullets are tolerant about being oversize a bit, as long as they will load & chamber.  .323  vs. .321?  That os only.002.  Not much difference in cast bullet terms.  It is often recommended to size your cast bullets .001 over groove diameter.

Offline Kywoodwrkr

  • Trade Count: (0)
  • Member
  • *
  • Posts: 79
Re: 32 cal bullets?
« Reply #6 on: December 21, 2006, 04:50:33 AM »
Were I to cast for the 32 Remington I'd look for Lyman moulds 3215,321232,321265,321297,321298,321317 or 321427.
Those are listed in the Lyman cast Bullet Handbook.
FWIW
DaveP    kywoodwrkr
DaveP   Kywoodwrkr

Offline Bitterroot Bob

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 249
Re: 32 cal bullets?
« Reply #7 on: December 27, 2006, 07:57:22 AM »
Howdy,
Cabela's in Michigan had a Model 14 in .32 Remington for a while. I investugated moulds and found that Lee makes a 170-grain gas-checked round-nose that would work pretty well. There are Lyman RN's designed for the Remington, but I would put those in the "Collector Mould" category. I'm just not sure if it is worth paying more for an original, than to have a custom mould cut.
Keep checking eBay and be patient, or try the Lee.

Bitterroot