Author Topic: Reduced loads  (Read 1079 times)

0 Members and 1 Guest are viewing this topic.

Offline seafox

  • Trade Count: (0)
  • Member
  • *
  • Posts: 22
Reduced loads
« on: January 20, 2007, 08:19:27 AM »
I have a 1917 Enfield 30/06 that kicks so hard I can't help but flinch when I shoot it. I just shoot paper at 100 yds. so I don't need a long range load. I use Varget powder and Speer 150 gr. bullets. What would be a good absolute minimum powder charge and/or different bullet weights that would lessen recoil ? Also, please explain detonation due to too small a powder charge.

Offline Almtnman

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 853
  • Gender: Male
  • Walk softly and carry a big stick!
    • The Mountain
Re: Reduced loads
« Reply #1 on: January 20, 2007, 11:05:23 AM »
If the kick is bothering you that much with it, why don't you have a Limbsaver recoil pad installed on it? That'd make it more pleasant to shoot.
AMM
The Mountain
"The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government."~~Thomas Jefferson

Offline Robert

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1618
Re: Reduced loads
« Reply #2 on: January 20, 2007, 11:10:10 AM »
Congrats on a wonderful old firearm.  I have two.  I converted on to 35 Whelen Ackley.  There are a few different powders that will work with reduced loads.  My favorite is Accurate Powder's xmp5744.  I have had great success with even with an Ultra-Mag.  It is a bulky powder and not 'position sensitive'.  Ok...I will explain that...and some of the inherent danger working with reduced loads.  If the case is filled less than 40% with some powders, the primer flash can just go up the entire length of the cartridge and ignite the powder too fast.  There are other factors as well, but I have been told this is the main problem.  However....I think that MOST explosive accidents result from a bullet becoming lodged in the bore and then firing another behind it.  If you use reduced loads.....MAKE ABSOLUTELY SURE THAT THE BULLET HAS HIT THE TARGET AND IS NOT STUCK!   If in doubt, pull the bolt and LOOK down the barrel.  You can also use a cleaning rod and run it down the barrel to check for obstruction if your bolt does not come out easily or if it is another type of firearm.  Whatever you do.....Make sure you use tested load data.  Accurate has a lot of the reduced data on their website and in the reloading manual.  Speer's manual also has a lot of reduced load data with various powders, and there are others.  Be safe....keep your face and your eyes.
....make it count

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Reduced loads
« Reply #3 on: January 20, 2007, 01:31:13 PM »
Hodgdon offers some reduced loads using H4895 and lighter bullets. Greg Mushial has a bunch of low velocity cast data too.

Tim

http://www.hodgdon.com/data/youth/30-06_y.php

http://www.gmdr.com/lever/lowveldata.htm
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Ranger J

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 990
  • Gender: Male
Re: Reduced loads
« Reply #4 on: January 21, 2007, 05:37:30 AM »

I loaded some 150G SP with 2400 one time for my daughter to shoot.  They did not have enough ump to cycle a 742 Remington but shot good out of it.  They should work well in a bolt.  I think I got the load out of the #1 Lee manual.
RJ


Offline MnMike

  • GBO Supporter
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 493
Re: Reduced loads
« Reply #5 on: January 24, 2007, 01:58:57 PM »
Another possible reason for "detonation" is with a 40% fill, it is possible to double charge a case without it dribbling over the reloading table. I load light varmit loads with 110gr bullets for my 30-06 and shoot some .45ACP velocity plinking loads with my .45 Win Mag. I am going to work up some 22 hornet loads for my .223 when I get the chance. It is a fun thing to play with. In Lee's reloading book, there is a discussion of reduced loads. I found it worth reading.

mike
Mike Ellestad

Offline Gregory

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1482
  • Gender: Male
Re: Reduced loads
« Reply #6 on: January 24, 2007, 04:02:02 PM »
Also, please explain detonation due to too small a powder charge.

A good read

http://www.reloadammo.com/liteload.htm
Greg

NRA Endowment Life Member
the right of the people to keep and bear arms shall not be infringed.
Second Amendment, U.S. Constitution (1791)

Offline Wingman26

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 248
  • Gender: Male
    • Wingman 26 Home Page
Re: Reduced loads
« Reply #7 on: January 24, 2007, 06:50:57 PM »
Because of arthritis I have been loading the youth loads as shown on Hodgdon's web site, it really helps on the calibers that are kickers!
John
Site Staff  http://mp-pistol.com/
Cum catapultae proscriptae erunt tum soli proscript catapultas habebunt

Offline ron haralson

  • Trade Count: (0)
  • Member
  • *
  • Posts: 70
Re: Reduced loads
« Reply #8 on: January 25, 2007, 07:32:40 PM »
I use 17gr 2400 with lyman 31141, 311284, 311299(the .303 bullet) or 311365. Noise and recoil are very light, and I get accuracy comparable to my jacketed loads in my 1917 enfield.

I've had very similar results with 16 - 17gr H110, and reasonable results with 9 - 12gr Unique, these loads also reasonable results with Lee 150gr flatnose mold.

Cheap too!

Offline jgalar

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1231
  • Gender: Male
Re: Reduced loads
« Reply #9 on: January 26, 2007, 02:34:17 AM »
Here is a long reprint of an Ed Harris article about using reddot for rifle loads. I posted this here a couple of years ago, but without the search feature it would be hard to find.....

Date: 17 Feb 94  17:50:11
From: Ed Harris
To:   All
Subj: Red Dot in Reduced Rifle Loads

"The Load" is 13 Grains of Red Dot" (In most strong-actioned, military rifles
of .30 cal. or larger)  READ ON FOR SPECIFICS AND WARNINGS!
 
(If you missed this article when it originally appeared in Handloader's
Digest, 10th Edition, here it is again...

By C.E. (Ed) Harris, Revised 2-16-94

My success in economizing by using up leftover shotshell powder
has changed my approach to handloading.  I had a caddy of Red
Dot, and no longer reloaded shotshells, so asked myself, "what
can I do with it?"  My shooting is now mostly high-power rifle.
I needed several hundred rounds a week to practice offhand,
reloading, and working the bolt in sitting and prone rapid, but
didn't want to burn out my barrel or my wallet.  Powder used to
be cheap, but today is $20/lb. (or more), so cost is a factor in
component choice.

I used to ignore pistol or shotgun powders in reduced rifle loads
for the usual reasons: the risk of accidental double-charges,
fears of erratic ignition, and concerns with maintaining
accuracy, and reduced utility with a low-power load. Still, the
caddy of Red Dot kept "looking at me" from the corner. Would it
work? Looking at data in the RCBS Cast Bullet Manual No. 1 and
the Lyman Cast Bullet Handbook suggested it would, so I tried it,
much to my delight!  Red Dot is bulky, compared to the usual
rifle powders used in .30-'06-size cases. It occupies more powder
space in typical charges than common "reduced load" rifle
powders, such as #2400, IMR4227, IMR4198 or RL-7. The lower bulk
density of Red Dot adequately addresses my safety concerns
because it makes an accidental double charge far less likely.

After considerable experimentation, my friends and I found "The
Load" is 13 grains of Hercules Red Dot, in any FULL SIZED rifle
case of .30 cal. or larger. "The Load" has distinct advantages
over more expensive alternatives, within certain limitations,
which are:

1. The case must be LARGER than the .300 Savage or .35 Remington.

2. The rifle must be of MODERN (post 1898) design, suitable for
smokeless powder, with a bore size of .30 cal. or larger.

3. The bullet weight must be within the NORMAL range for the
given cartridge.

4. Inert fillers such as Dacron, kapok or are NOT RECOMMENDED!
(Nor are they necessary).

Within these restrictions I have now engraved in stone, "The
Load" works! The bullet may be either jacketed or cast.
Gaschecked cast bullets required in the .30 cals., otherwise you
will get leading, but plainbased ones work fine in the 8mm Mauser
or larger.

"The Load" has shown complete success in the .30-40 Krag, .303
British, 7.65 Argentine, .308 Win., 7.62x54R Russian, .30-'06,
8x57 and .45-70 (strong-actioned rifles such as the 1886
Winchester or 1895 Marlin -- 12 grs. is maximum for 400 gr.
bullets in the Trapdoor Springfield -- Ed.) Though I have not
tried it, I have no doubt that "The Load" would work well in
other cartridges fitting these parameters, such as the .35
Whelen, .358 Winchester, .375 H&H or .444 Marlin, based on RCBS
and Lyman published data.

"The Load" fills 50% or more of a .308 Win or .30-'06 case. The
risk of an accidental double charge is greatly reduced, because
the blunder is immediately obvious if you visually check, powder
fill on EVERY CASE, as you should whenever handloading!  A bulky
powder measures more uniformly, because normal variation in the
measured volume represents a smaller percentage of the charge
weight.

Red Dot's granulation is somewhat less coarse than other flake
powders of similar burning rate, such as 700-X, which aids
metering.  Its porous, uncoated flakes are easily ignited with
standard primers.  So-called "magnum" primers do no harm in cases
larger than the .30-'06, but are neither necessary nor
recommended in smaller ones. I DO NOT recommend pistol primers in
reduced rifle loads, because weak primers may cause erratic
ignition, and their thinner cups can perforate more easily,
causing gas leakage and risk of personal injury!

The velocities obtained with 13 grs. of Red Dot appear mild, but
"The Load" is no pipsqueak!  In a case like the .308 or .30-'06,
you get (from a 24" sporter barrel) about 1450 f.p.s. with a 200-
gr. cast bullet, 1500 with a 170-gr., or 1600 with a 150-gr. cast
load.  "The Load" is fully comparable to "yesterday's deer
rifle", the .32-40, and provides good expansion of cheap, soft
alloys (10-13 BHN) at woods ranges.  Jacketed bullet velocities
with "The Load" are about 120-150 f.p.s. less than a lubricated
lead bullet of the same weight.

Longer-barreled military rifles pick up a few feet per second,
but "The Load" starts to slow down in barrels over 28", such as
the M91 Moisin-Nagant and long Krags or 98a Mausers.

My preferred alloy in the .30 cals. is a mixture of 3-5 lbs. of
.22 backstop scrap to 1 lb. of salvaged linotype.  Wheelweights
also work well, as do soft "Scheutzen" alloys such as 1:25
tin/lead. in bores of 8 mm or larger.  "The Load" drives soft-
cast .30-cal. to 8 mm bullets fast enough to get expansion, but
without fragmenting. These out-penetrate factory .30-30
softpoints, and kill medium game up to 150 lbs. well at short
ranges up to 100 yards, when placed accurately. In medium and
large bores like the .375 H&H or .45-70, "The Load" gives typical
black powder ballistics for the bore. A 255-265 gr. cast bullet
in the .375 H&H approximates the .38-55 at 1330 f.p.s. Soft 300-
405-gr. cast bullets are pushed at 1300-1350 f.p.s. from a 22"
barrel .45-70, sporter are very effective on deer at woods
ranges.  Cast bullets over .35 cal. do not have to expand
appreciably to work well on game if blunt and heavy for their
caliber.

The Load" works well with jacketed bullets, giving somewhat lower
velocities than with cast lead, due to less effective obturation
and greater friction in the bore. The 85-gr. or 100-gr. Hornady
or 90-gr. Sierra JHP for the .32 H&R Mag. revolver, or the
Remington 100-gr. .32-20 softpoint bullet become mild, but
destructive varmint loads at 1600 f.p.s. from a .308 or '06.

If you substitute a stiffly jacketed 110-gr. .30 Carbine
softpoint bullet, designed for higher velocities than imparted by
"The Load",  you have a non-destructive "coup de gras", small
game or wild turkey load which shoots close to your deer rifle's
normal zero, but at 25 yards! A more accurate and effective small
game or varmint load uses a flat-nosed 150-gr. pr 170-gr. .30-30
bullet instead.  These don't expand at the 1400-1450 f.p.s.
obtained with "The Load", but their larger frontal area improves
killing power compared to roundnoses or spitzers.

I have use pulled GI .30 caliber Ball, and Match bullets with
"The Load" for cheap 200-yd. NMC boltgun practice. Accuracy is
equal to arsenal loads, but I use my 600-yard sight dope at 200
yards.  I expect 5-6" ten-shot, iron-sight groups at 200 yards
using M2 or M80 pulled bullets and about 3-4" for the M72 or M118
Match bullets. I use these mostly in bolt-action rifles, but they
can be single-loaded for offhand or slow-fire practice ion the
Garand as well.  These .30 cal. pulls shoot fine in the .303
British or 7.62x54 Russian, despite their being a bit small,
because the fast-burning Red Dot upsets them into the deeper
grooves. The 173-gr. Match .30 cal. boattail bullets may not
shoot as well at these low velocities as lighter flat bases in
the 12" twist .308 Win. barrels, but they do quite well in ten-
inch twist barrels such as in the '06, 7.62 Russian, .303 British
and 7.65 Argentine.

The longer bore time of these 1400 f.p.s. (typical 170-180-gr.
jacketed load velocity) practice loads makes errors in follow-
through apparent, a great practice and training aid. The light
recoil and lower report of these loads helps transition Junior
tyro shooters from the .22 rimfire to the service rifle without
being intimidated by the noise and recoil.

Zeroing is no problem in the M1 or M14, because "The Load" shoots
into the ten-ring of the reduced SR target at 200 yards from your
M1 or M14 rifle at using your normal 600 yard sight dope!   The
somewhat greater wind deflection blows you into the "8" ring at
200 yards with the same conditions you would expect to do so at
600 yards with M118 Match ammunition. This provides your Junior
shooters some useful wind-doping practice.

The economy of a lighter charge is obvious.  A full power .30-'06
load using 50 grs. of an IMR powder like 4064 costs 10 cents a
pop, just for powder, at 140 rounds per pound (if you are lucky
enough to find new powder for $14/lb.).  Substituting 13 grs. of
Red Dot gets 538 rounds per pound at a cost of 2.6 cents which is
a savings of over $7 per hundred rounds in powder alone! Greater
savings are possible if you get the best price and buy powder by
the caddy.

Velocity and point of impact of "The Load" is not noticeably
affected by varying powder position in the case. I shoot them
either slow fire, or clip-fed and flipped through rapid-fire in
the boltgun with equal accuracy.  Red Dot is very clean burning
and is economical both on the basis of its lower charge weight,
and its lower basic cost per pound compared to other "rifle"
powders.

Best of all, using a shotshell powder I already have reduces the
kinds of powder I keep and eliminates the need for a special
"reduced load" powder. This approach is ideal for rifle shooters
who are also shotgunners, since almost everybody who reloads for
12-ga. probably has a keg of Red Dot already!

I now realize it is foolish to use heavier charges of more
expensive powder for routine practice, varmint or small game
loads in my center-fire rifles. I seldom shoot at over 200 yards,
and don't enjoy wearing out expensive target barrels
unnecessarily.  Since I already have good sight dope and need to
work more on technique and save my remaining barrel accuracy life
for matches.

I am glad I found the way to get alot more shooting for the
dollar. Economical powder choice IS possible, and my reloading
has become less complicated and more enjoyable simple since I
realized I could do most of my rifle shooting with 13 grains of
Red Dot!


In Home Mix We Trust, Regards, Ed