« previous next »
Pages: [1]   Go Down

Author Topic: .22-250 Handi  (Read 776 times)

0 Members and 1 Guest are viewing this topic.

Offline navylawdog

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 410
  • Gender: Male
.22-250 Handi
« on: February 08, 2007, 04:45:59 PM »
I have been reading alot of the threads here in the H&R and NEF rifle category but I have yet to find a thread about the .22-250. I have just purchased one and unfortunately have not had the time to take it out and shoot it. :'( So I was wondering if anyone can tell me what to expect from my new purchase.

Navylawdog
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: .22-250 Handi
« Reply #1 on: February 08, 2007, 05:00:21 PM »
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline stimpylu32

  • Moderators
  • Trade Count: (67)
  • Senior Member
  • *****
  • Posts: 6062
  • Gender: Male
Re: .22-250 Handi
« Reply #2 on: February 09, 2007, 03:22:48 AM »
navylawdog

I got a 250 for CHRISTmas this year , first time i took it out i was getting under 1" at 100 , just make sure you clean it WELL , sometimes the factory leaves quite a bit of gunk in them , can't give you any idea as far as factory ammo , i have only shot handloads in mine .

And welcome to GBO and the wild world of Handi's .

stimpy
Logged
Deceased June 17, 2015


:D If i can,t stop it with 6 it can,t be stopped

Offline navylawdog

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 410
  • Gender: Male
Re: .22-250 Handi
« Reply #3 on: February 09, 2007, 06:28:11 AM »
I just want to say thank you to Tim for the links as I found them to be very helpful. Also thanks goes out to Stimpy for the tip I will be sure and do that.

Navylawdog
Logged

Offline HillBillyFarmer

  • Trade Count: (0)
  • Member
  • *
  • Posts: 78
Re: .22-250 Handi
« Reply #4 on: February 09, 2007, 09:43:39 AM »
Yup, you'll want to clean it good and keep it clean. Start with some 55gr remington core-loks. I found that mine didn't like the lighter bullets such as 45gr winchester white box. Good luck to you!
Logged

Offline sqeeter91

  • Trade Count: (0)
  • Member
  • *
  • Posts: 28
  • Gender: Male
Re: .22-250 Handi
« Reply #5 on: February 09, 2007, 11:37:22 AM »
Evening  Navy,
      I think you'll have a lot of fun with your 22-250. can't emphasize the "cleaning" enough. I'm very happy with mine. I don't shoot factory loads-So I can't help ya there. So far 55gr Sp with 4064 powder seems to shoot the best. All, I can say is that you'll love the guys on here. I've never seen another site where everyone is as helpful as the guys are on GB. I haven't shot mine out past 100yds yet, so I can't even tell you what to expect as far as bullet drop.
                                                                                                                              Enjoy,      Marc
Logged
Whether the target is paper, a can, or whatever. The objective is the same- Put it where the hairs cross.

Offline daddywpb

  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 1136
Re: .22-250 Handi
« Reply #6 on: February 10, 2007, 12:18:44 AM »
I have never had a Handi before, but I have been looking at buying one in 22-250. Lots of info here. Thanks to all.
Logged

Offline Jim Stacy

  • Trade Count: (11)
  • Contributor
  • ***
  • Posts: 309
Re: .22-250 Handi
« Reply #7 on: February 10, 2007, 07:58:00 AM »
Bought one in 22/250 and all I've shot in it so far is the Renington 50 grain (40 to a box) that I bought at Sportsman's Warehouse and it shoots those good. Will routinely shoot less than 1" for 3 of 5 shots . I usually take care of the other two going over 1" ! Mine is very sensitive to placement of the foreend on the sand bag , like most handi's are. Mine groups best when I place the take down screw on the foreend on the bag , not in front or behind or POI will shift an inch or so. I plan to do some of the techniques outlined in FAQ for foreend correction. I will try float first , easiest to do and glass baed lug and back to the frame if that doesn't fix it.
Logged
Pages: [1]   Go Up
« previous next »