« previous next »
Pages: [1]   Go Down

Author Topic: WW smelted, now want  (Read 818 times)

0 Members and 1 Guest are viewing this topic.

Offline 358jdj

  • Trade Count: (0)
  • Member
  • *
  • Posts: 38
WW smelted, now want
« on: February 20, 2007, 04:05:26 AM »
Thanks to help I received in response to my previous post, I got the batch of wheel weights smelted and into 2.2 pound ingots.  I don't really have the time and money to buy molds, sizer and luber at this point.  Looking through my catalogs last night I saw a Lee Tumble Lube casting mold.  It throws a 240 grain .430 SWC bullet.  According to the propaganda, this bullet does not need to be sized and can be tumble lubed in Alox.

I want to shoot the bullets I eventually make in a Ruger 4 5/8 blackhawk and a 1894 Marlin, both in 44 Mag.  My question is, would the tumble lube bullet get me buy for awhile or should I hold out until I can swing the whole setup?  I am not a big velocity fan.  My current load of IMR4227 gives me about 1150 fps in the pistol and 1500 in the Marlin with a 255 grain SWC GC.

Should I go on the cheap or wait for more $$$$?

Thanks.
Logged

Offline ND Sharpshooter

  • Trade Count: (0)
  • Member
  • *
  • Posts: 71
Re: WW smelted, now want
« Reply #1 on: February 20, 2007, 04:16:44 AM »
358jdj,

The Lee system works at the lower velocity levels.  It's messy, gums up the seater die, smells a bit, and smokes quite a bit.  I don't use it any more.  If I'd known then what I know now, I wouldn't have gone the tumble lube route at all.  That said, if you're planning to shoot thousands and thousands at cowboy action velocities, it saves a lot of time at the bench lubri-sizing. 
Logged
Never said I didn''t know how to use one.  :wink:

Offline Lloyd Smale

  • Moderators
  • Trade Count: (32)
  • Senior Member
  • *****
  • Posts: 18250
Re: WW smelted, now want
« Reply #2 on: February 20, 2007, 12:54:10 PM »
i dont care much for the bullet designs or the lube either but it will get you shooting your gun for alot less money then your paying now for bullets.
Logged
blue lives matter

Offline Cheesehead

  • GBO Supporter
  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 3282
  • Gender: Male
Re: WW smelted, now want
« Reply #3 on: February 20, 2007, 01:06:29 PM »
358

I am also starting to cast my own and using the tumble lube system. It works for my 44's. I have also bought a tumble lube mold for my 45 acp for making bullets for action pistol competition. My shootin buddy gave me 300 pounds of ww lead so I am set. I plan on upgrading some day.

Cheese
Logged
Nothing in the world is more dangerous than sincere ignorance.

Offline dubber123

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 435
Re: WW smelted, now want
« Reply #4 on: February 20, 2007, 02:27:01 PM »
Cheesehead, if you're shooting action pistol, that 300 lbs, is gonna go quick!  I've burned up about 15,000 rounds in the last 2 years playing that game.  If it weren't for casting, I couldn't afford to do it.
Logged

Offline Cheesehead

  • GBO Supporter
  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 3282
  • Gender: Male
Re: WW smelted, now want
« Reply #5 on: February 20, 2007, 03:33:53 PM »
I guess I am set to get a good start. Its all fun for me.

Cheese
Logged
Nothing in the world is more dangerous than sincere ignorance.

Offline ron haralson

  • Trade Count: (0)
  • Member
  • *
  • Posts: 70
Re: WW smelted, now want
« Reply #6 on: February 21, 2007, 05:54:52 AM »
While I can't speak to the .44 mold, I have the .30 cal TL bullet mold which works fine. You should know that if you aren't happy with Lee Liquid Alox, you can hand lube with most any decent machine or automotive grease(I use Canadian Tire Moly Grease) and get very decent results. Just seat the bullets onto the first driving band, finger fill the grooves with grease, seat the bullet to the finished depth and wipe the finished cartridge clean. Faster and easier than it sounds -  and cheap if cost is an issue. Best of luck.
Logged
Pages: [1]   Go Up
« previous next »