« previous next »
Pages: [1]   Go Down

Author Topic: Firing Pin Depth  (Read 619 times)

0 Members and 1 Guest are viewing this topic.

Offline mattparliament

  • Trade Count: (38)
  • A Real Regular
  • ****
  • Posts: 503
  • Gender: Male
Firing Pin Depth
« on: March 22, 2007, 10:54:49 AM »
Hey guys.  I was doing some thinking last night about the 35 whelen's and the misfires.  After some thought I grabbed the action and noticed that I could push the firing pin further forward with my finger than the hammer does.  I didn't measure it but it was obvious to the naked eye.  I wondered if shaving some material off of the hammer surface that hits the receiver would increase firing pin depth and help out with the misfires.  Has anyone tried this with any results?  Should I leave it the heck alone?  Is it possible to have a firing pin strike too deep?  Any thoughts?
Logged
Life is tough, it's tougher if you're stupid.  ~John Wayne

Offline PartsMan

  • GBO Supporter
  • Trade Count: (7)
  • Senior Member
  • *****
  • Posts: 1351
  • Gender: Male
  • Proud Handi Owner
    • myspace
Re: Firing Pin Depth
« Reply #1 on: March 22, 2007, 11:04:13 AM »
Somebody did that on another rifle.
It worked but be carful not to puncture primers.
Also it will have to be checked with accesory barrels.
Logged

Offline Fred M

  • GBO Supporter
  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 2362
    • Fred The Reloader and Wildcatter
Re: Firing Pin Depth
« Reply #2 on: March 22, 2007, 11:27:05 AM »
Matt.
Many bolt actions have  0.055" f-pin protrusion. My two Handi's had 0.035" and I increased that to 0.045". Punching through a primer takes a lot more impact than a Handi can provide. That is with a nicely rounded  f-pin.

Most of the no spark came from a weak hammer spring together with hard primers.
You can look at my web site and learn how I tuned the f-pin and pin seat.

Very few bolt actions with 0.055" protrusion will punch through a primer with a well rounded f-pin.
Logged
Fred M.
From Alberta Canada.

Offline Walks with a gimp

  • Trade Count: (0)
  • Member
  • *
  • Posts: 81
Re: Firing Pin Depth
« Reply #3 on: March 22, 2007, 02:45:56 PM »
  I miked the length of the hammer and took .010" off the face of the hammer with a belt sander and no more misfires in my 500 S&W. Before the modification it would only fire about 50% of the time.
Logged

Offline mattparliament

  • Trade Count: (38)
  • A Real Regular
  • ****
  • Posts: 503
  • Gender: Male
Re: Firing Pin Depth
« Reply #4 on: March 23, 2007, 03:59:32 AM »
Thanks for the info guys, I'll have to measure it and see if this is my next project.  I'll have to try one of the rounds that I saved that were "misfires" and see if it will touch off.
Logged
Life is tough, it's tougher if you're stupid.  ~John Wayne

Offline Walks with a gimp

  • Trade Count: (0)
  • Member
  • *
  • Posts: 81
Re: Firing Pin Depth
« Reply #5 on: March 23, 2007, 01:40:23 PM »
  All the mis-fires that I had with my .500 went off with the second hit.
Logged

Offline mattparliament

  • Trade Count: (38)
  • A Real Regular
  • ****
  • Posts: 503
  • Gender: Male
Re: Firing Pin Depth
« Reply #6 on: March 31, 2007, 01:55:35 PM »
just measured mine and it is .042", think that's enough?  I've used my 270, 45-70, any 22 hornet all on the same frame without a misfire.  Maybe I should leave well enough alone and use Fred's cream of wheat recipe to fire-form my whelen brass before I load them up, may be a simpler answer...  any thoughts?
Logged
Life is tough, it's tougher if you're stupid.  ~John Wayne

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Firing Pin Depth
« Reply #7 on: March 31, 2007, 02:03:11 PM »
Here's a previous thread with some pertinent info by Fred.

Tim

http://www.graybeardoutdoors.com/smf/index.php/topic,80643.msg496285.html#msg496285
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain
Pages: [1]   Go Up
« previous next »