« previous next »
Pages: [1]   Go Down

Author Topic: Reloading dies for a K31  (Read 764 times)

0 Members and 1 Guest are viewing this topic.

Offline bulletfmj

  • Trade Count: (1)
  • Posts: 4
Reloading dies for a K31
« on: July 24, 2008, 11:28:12 AM »
Just picked up a K31 rifle,all matching numbers and very nice bore,also has name tag under stock plate.Bought some ammo,(prvi partizan) sp 174 gr. mainly for casing.Would like to start reloading for it but have heard different opinions on dies.Hopefully someone can guide me in the right direction.Thanks,Bill
Logged

Offline blackpowderbill

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 287
  • Gender: Male
Re: Reloading dies for a K31
« Reply #1 on: July 24, 2008, 11:49:53 PM »
e been using Lee Dies for My K31 for the last four years and am 100 percent satisfied with them. $19.95.
Logged
People are like slinkies, they serve no purpose yet they bring a smile to your face when you push them down the stairs.

Offline Czech_too

  • Trade Count: (24)
  • Contributor
  • ***
  • Posts: 350
  • Gender: Male
Re: Reloading dies for a K31
« Reply #2 on: July 25, 2008, 12:49:25 AM »
While I do use Lee Dies in some calibers, I'm going to use Redding Dies for the K31.  They may be pricey but after the last set of Lee dies that I bought, for the 7.62x25, I'll spend the extra money and get it right the first time.  Just my opinion.
http://www.surplusrifle.com/reloading.asp

Brian, in Ohio
Logged
NRA Life Member
Cruffler
INOA

genealogy, another area of interest

Offline MGMorden

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 2093
  • Gender: Male
Re: Reloading dies for a K31
« Reply #3 on: July 25, 2008, 07:59:51 AM »
My Lee dies for 7.5x55 came with the decap pin off-center (it was bent a bit).  They did send a new one though that worked fine. 

Just curious Czech_too: what problems did you have with your 7.62x25 dies? If it's the same problem I had (rounds not chambering after seating a bullet), then I have a solution for you :).
Logged

Offline 1911crazy

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4793
  • Gender: Male
Re: Reloading dies for a K31
« Reply #4 on: July 26, 2008, 05:07:01 AM »
After running 6k of 308 thru my $8 LEE RGB dies without a problem I purchased all my military calibers in Lee dies.  I even purchased my modern calibers in the Lee Brand too.  They fit my RCBS rockchucker press perfect.
Logged

Offline STUMPJMPR

  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 1037
Re: Reloading dies for a K31
« Reply #5 on: July 30, 2008, 07:47:24 AM »
I used Lee for all of my shooting....Never had a problem with them...
Logged

Offline hazmt

  • Trade Count: (0)
  • Member
  • *
  • Posts: 33
Re: Reloading dies for a K31
« Reply #6 on: July 30, 2008, 03:22:43 PM »
It really doesn't matter which dies you use for the 7.5 swiss as long as you set the press up to full length size the case properly. Most folk's who've had trouble with the Lee dies didn't adjust the dies to fully contact the shell holder, then lift the ram and screw the die  in about another 1/4 turn. If you don't have a little camming action at the end of the press stroke, then the striaght pull cases won't  fire. Just a little pointer I've learned through trial and error. I use Lee dies to load for all my 7.5 Swiss rifles and they work great. Just my 2 centos, your mileage may vary!

Best regards!

Haz
Logged

Offline RaySendero

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1064
  • Gender: Male
Re: Reloading dies for a K31
« Reply #7 on: July 30, 2008, 04:50:25 PM »
I have both Lee dies and Redding dies for my 7.5x55.

Anyone want to buy the Lee?
Logged
    Ray
Pages: [1]   Go Up
« previous next »