« previous next »
Pages: [1]   Go Down

Author Topic: anyway to mount Reddot on a NEF without drilling?  (Read 1046 times)

0 Members and 1 Guest are viewing this topic.

Offline Hunter_Smurf

  • GBO Supporter
  • Trade Count: (12)
  • Avid Poster
  • *****
  • Posts: 177
  • Gender: Male
anyway to mount Reddot on a NEF without drilling?
« on: April 21, 2008, 04:24:29 PM »
i have a red dot scope and a NEF 12 gauge shotgun...

it is going to cost me almost $50-$75 to get it drilled and tapped and put a rail on it...

I DON'T WANT TO PAY THAT FOR THIS GUN....


Do they make any attachment or anything i might not know about ? that would allow this to happen?

I'm not finding anything but with more eyes looking and more knowledge from you all... I'm hoping...lol
Logged
I'm not laughing at you I'm laughing with you,
                             Your just not laughing.......

Ever notice the deer we get is always smaller
                              than the deer we saw..??.lol

Offline Mohawk

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1958
Re: anyway to mount Reddot on a NEF without drilling?
« Reply #1 on: April 21, 2008, 08:52:14 PM »
    Don't know of any but if it helps they make very bright tritium front sights that clamps on to the barrel just behind the bead at the muzzle. This would make a good alternative if the red dot you had in mind did not use magnification.
Logged

Offline Mike Bell

  • Trade Count: (0)
  • Member
  • *
  • Posts: 6
Re: anyway to mount Reddot on a NEF without drilling?
« Reply #2 on: June 02, 2008, 05:19:40 PM »
Im about to find out.  I made a mount that is held on by the forend screw. 
http://www.gboreloaded.com/forums/index.php/topic,145760.0.html

We will see if it holds up when I get a dot or halo sight for it.

 
Logged

Offline Winter Hawk

  • Trade Count: (47)
  • Senior Member
  • *****
  • Posts: 1947
  • Gender: Male
Re: anyway to mount Reddot on a NEF without drilling?
« Reply #3 on: June 03, 2008, 07:48:17 AM »
Dang!  Didden you boys ever hear of Duct Tape?  If it can keep a super cub flying, it sure ought to hold a little bitty scope on a shotty-gun!  Iffen you use enough of it, that is..... 

-WH-
Logged
"All you need for happiness is a good gun, a good horse and a good wife." - D. Boone

Offline STUMPJMPR

  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 1037
Re: anyway to mount Reddot on a NEF without drilling?
« Reply #4 on: June 03, 2008, 08:03:00 AM »
This is how i did mine...The loctite blackmax should work great for the scope base soft solder would also work....Just  be careful some solders arent' great for aluminum....everything cost me about $80 but i am more than pleased with the results...


These are midway item numbers
285564   Williams Fire Sight Rifle Bead .450" Height, .250" Width Steel Blue 3/32" Fiber Optic Red(front sight needs to be a little taller)   
330260   Loctite 380 Instant Adhesive Black Max 3 gm   
496762   Williams WGRS-Guide Receiver Peep Sight "Ghost Ring" Aperture Aluminum Black   
687196   Williams Shotgun Shorty Ramp 12 Gauge 1/8" (.875) Blue   
698217   Williams WGRS-H&R Guide Receiver Peep Sight H&R 158, 258 Topper Single Shot Rifles, Ruger Mark 2 Aluminum Black
Logged
Pages: [1]   Go Up
« previous next »