« previous next »
Pages: [1]   Go Down

Author Topic: Rcbs small base dies  (Read 303 times)

0 Members and 1 Guest are viewing this topic.

Offline Inrut24/7

  • Trade Count: (6)
  • Contributor
  • ***
  • Posts: 338
  • Gender: Male
Rcbs small base dies
« on: March 22, 2009, 05:14:30 AM »
These dies are supposed to set the shoulder back slightly more and size the body smaller for use in semi auto, pump and lever guns.   I am thinking of trying a set for loading my 223 ultra varmint,  I have polished the chamber a few times, but still get stuck cases after my brass has been loaded two or three times.   I have never had a stuck case with factory ammo or the first time loading new brass, so im thinking these dies might be the awnser, and i dont think accuracy will go away, because my gun shoots the same groups with new brass and older brass.   Has anybody tried these dies?
Logged

Offline canon6

  • GBO Supporter
  • Trade Count: (119)
  • Senior Member
  • *****
  • Posts: 1508
  • Gender: Male
Re: Rcbs small base dies
« Reply #1 on: March 22, 2009, 05:22:52 AM »
I have used them for a pump 30-06, but not for a Handi.Not meaning to offend , but you are trimmimg the cases ,aren't you.????  I have a 30-30 that if the cases were not trimmed they would stick.    hth   Doug
Logged
a armed man is his own master

Offline Inrut24/7

  • Trade Count: (6)
  • Contributor
  • ***
  • Posts: 338
  • Gender: Male
Re: Rcbs small base dies
« Reply #2 on: March 22, 2009, 05:27:46 AM »
yep, I trim them with a lee case trimmer ;)
Logged

Offline Inrut24/7

  • Trade Count: (6)
  • Contributor
  • ***
  • Posts: 338
  • Gender: Male
Re: Rcbs small base dies
« Reply #3 on: March 23, 2009, 02:58:48 PM »
ttt
Logged

Offline billy_56081

  • GBO Supporter
  • Trade Count: (5)
  • Senior Member
  • *****
  • Posts: 8575
  • Gender: Male
Re: Rcbs small base dies
« Reply #4 on: March 23, 2009, 03:02:48 PM »
Until I got a Handi, I didn't full lenght size, after getting a handi I started full length resizing and had the same problems as you. I started watching closer and making sure the shell holder actually touched the die hard. I learned that I was not pushing the shoulder back only bumping it. After I truly full length sized them I hadno more issues.
Logged
99% of all Lawyers give the other 1% a bad name. What I find hilarious about this is they are such an arrogant bunch, that they all think they are in the 1%.

Offline billy_56081

  • GBO Supporter
  • Trade Count: (5)
  • Senior Member
  • *****
  • Posts: 8575
  • Gender: Male
Re: Rcbs small base dies
« Reply #5 on: March 23, 2009, 03:04:13 PM »
And I thought about the small base dies too, until I figured out I wasn't sizing enough.
Logged
99% of all Lawyers give the other 1% a bad name. What I find hilarious about this is they are such an arrogant bunch, that they all think they are in the 1%.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43302
  • Gender: Male
Re: Rcbs small base dies
« Reply #6 on: March 23, 2009, 03:04:58 PM »
I'd tune the ejector per the FAQs before I invested in new a new die, polishing the chamber is just part of the fix for sticking brass other than the usual suspects, dirty/oily chamber or brass and loads that are too hot or haven't been fully resized so it fits flush to the chamber face before reloading as Billy mentioned.  ;)

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain
Pages: [1]   Go Up
« previous next »