« previous next »
Pages: [1]   Go Down

Author Topic: Need a source  (Read 379 times)

0 Members and 1 Guest are viewing this topic.

Offline Chas.

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 256
Need a source
« on: July 30, 2009, 02:09:33 PM »
Just wondering where everybody is getting those brass pin punches that you need to remove the Handi sights and trigger group.  Any help?
Logged

Offline gendoc

  • SWAMP GROCERIES RULE !!!
  • Trade Count: (329)
  • Senior Member
  • *****
  • Posts: 3957
  • TRUTH AND HUMOR, thatsa what i'm talk'n bout
Re: Need a source
« Reply #1 on: July 30, 2009, 02:14:30 PM »
SEARS has them... at least roun here they do!!
or snap-on, matco, or mac tool guys also.
might try midway or brownells
Logged
sea-ya.....
in tha meen time, i'm wait'n for tha  7th trumpet ta sound !!!

gotta big green tractor ana diesel truck, my idea of heaven's chasin whitetail bucks and asa country boy, you know i can survive............

hey boy, hit this mason jar one time...
burn ya lil'bit did'nt it. ya ever been snipe hunt'n ?  come on...

I prefer dangerous freedom over peaceful slavery.

Offline PHATINJUN

  • "Seeker of the Red Mist"
  • GBO Supporter
  • Trade Count: (144)
  • Senior Member
  • *****
  • Posts: 4076
  • Gender: Male
Re: Need a source
« Reply #2 on: July 30, 2009, 03:23:56 PM »
Nanchez , Sportsmansguide, Brownells , Cheaper Than Dirt , Midway ,Cabela's , Harbor Frieght just about anyone who sells gunsmithing stuff. Kurt
Logged
Deceased 2/16/24
https://www.dignitymemorial.com/obituaries/machesney-park-il/kurt-heckman-11671764

Sportster17M2,20"Nickle410Tamer,26"410,
WTUTI12ga,WTU25-06,M158 22RemJet, 24"Ultra.204Ruger24"UltraFluted.204Ruger
M157Mannliker.22Hornet,24".223UltraFluted,   24".223Ultra,7X64BrenekkeUltra,22-250AIUltraFluted            7.62x39,22"303Britstub.32H&Rmag, .32303BritstubHuntsman,24" SS.50calHuntsman 58calHuntsman 12gaHuntsman
NEF RevolversSSModel73.32H&Rmag                     Blued Model73.32H&R mag The herd is shrinking!!
                                 "SOLI DEO GLORIA"

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Need a source
« Reply #3 on: July 30, 2009, 03:48:37 PM »
I have some brass punches, but the small ones don't work very well on pins that have never been removed, they just bend, they work fine for reinstalling the pins tho.  I just use steel pin punches to knock them out, I used a small stone in the dremel to make them cup points so they self center on the round headed pins. Brownell's sells a small one for the front trigger guard pin, it's listed for use on a handgun.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Chas.

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 256
Re: Need a source
« Reply #4 on: July 31, 2009, 04:17:10 PM »
Thanks to all for tips and references.  I have ordered a set of 8 brass pin punches.  Dang, all these hobbies can get expensive.  Since retirement, I've collected way too many hobbies and need to thin the herd down.
Logged
Pages: [1]   Go Up
« previous next »