« previous next »
Pages: [1]   Go Down

Author Topic: 223 short neck chamber  (Read 566 times)

0 Members and 1 Guest are viewing this topic.

Offline ssjohnnie

  • Trade Count: (0)
  • Member
  • *
  • Posts: 50
223 short neck chamber
« on: December 28, 2009, 04:05:11 PM »
has anyone found this in there 223 i trim my cases to1.750 and found that this is about.010 longer than the neck of my chamber have been have some problems so now I trim to 1.740 and now it shoot a lot better and I can close gun without slaming it hard or more that once just something i found on mine. :)
Logged

Offline trotterlg

  • GBO Supporter
  • Trade Count: (36)
  • Senior Member
  • *****
  • Posts: 3978
  • Gender: Male
Re: 223 short neck chamber
« Reply #1 on: December 28, 2009, 04:33:26 PM »
I think you need to do a chamber cast and see what you really have, just from knowing how they are made and chambered it would be hard for me to believe you have a neck that is .020 short in yours.  I would look to other problems with the closing.  Larry
Logged
A gun is just like a parachute, if you ever really need one, nothing else will do.

Offline ssjohnnie

  • Trade Count: (0)
  • Member
  • *
  • Posts: 50
Re: 223 short neck chamber
« Reply #2 on: December 28, 2009, 05:19:28 PM »
I am sorry i forgot to say i DID take a chamber cast and it is 1.750 from chamber face to end of neck i trim to 1.740 now 
Logged

Offline necchi

  • GBO Supporter
  • Trade Count: (40)
  • Senior Member
  • *****
  • Posts: 1842
  • Gender: Male
Re: 223 short neck chamber
« Reply #3 on: December 28, 2009, 05:30:58 PM »
Wow, that is an odd one in the bunch,,all I've ever heard was long-looong, My cerrosafe casting came out at 1.79
Logged
found elsewhere

Offline trotterlg

  • GBO Supporter
  • Trade Count: (36)
  • Senior Member
  • *****
  • Posts: 3978
  • Gender: Male
Re: 223 short neck chamber
« Reply #4 on: December 28, 2009, 06:00:59 PM »
I think you need to measure the neck length and the chamber face to the sholder, my guess is the chamber is short.  For the neck to be short and the chamber the proper length to the sholder, the reamer used would have to have a short neck ground into it.  Then there would be hundreds of these short neck chambers out there, plus the maker of the reamer would have had to make it short and then ship it to H&R and have H&R QC miss it.  I just doubt you have what you think you have.  Larry
Logged
A gun is just like a parachute, if you ever really need one, nothing else will do.

Offline ssjohnnie

  • Trade Count: (0)
  • Member
  • *
  • Posts: 50
Re: 223 short neck chamber
« Reply #5 on: December 29, 2009, 10:54:46 AM »
here are my chamber mers. form base of chamber to sholder is 1.438 from base to bottom of neck is1.557 from base to end of neck 1.750 don't care what you say but neck is .010 short of what most are chamber is right to base of neck and there may be alot of them out there how many people take a chamber cast..... this just what i found on mine ;)
Logged

Offline jgore31

  • Trade Count: (0)
  • Posts: 4
Re: 223 short neck chamber
« Reply #6 on: December 29, 2009, 07:14:06 PM »
OP,
You DO know you can suppress a 357 magnum handi...DIDN'T YOU?
yhm wraith 9mm will bring the levels of a hot 357 to a 22 lr during warm days and a tad louder on cold nights..38 is sub and can't be heard over 75 yards away.
In my experiences anyhow..

BTW, 158 gr flat nose at 175 WILL take a coyote when backed by 16 gr H110.......
Those pesky 125 gr HP's just bounce right off. Something about the momentum or something.

James
Logged
Pages: [1]   Go Up
« previous next »