« previous next »
Pages: [1]   Go Down

Author Topic: forming 308 brass to 7mm08?  (Read 1862 times)

0 Members and 1 Guest are viewing this topic.

Offline DEACONLLB

  • GBO Supporter
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 2458
  • Gender: Male
forming 308 brass to 7mm08?
« on: March 14, 2010, 04:58:57 PM »
If I get some 308 brass how do I form it to 7mm08, Do i just size it in a 7mm08 die,  what is the process?
Logged
Korean war vet. NRA Member
Fourth fighter wing K14 Kimpo Korea 1952 Fourth but first, the mig killers.
533rd material ,air defense Oxnard AFB 1953-1955
Pastor of the  CBCG-Fellowship group Tulsa Oklahoma.

Offline mrjbloomington

  • Trade Count: (2)
  • Member
  • *
  • Posts: 71
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #1 on: March 14, 2010, 05:54:11 PM »
How is 308 brass reformed to 7mm-08 brass?
Logged

Offline mrjbloomington

  • Trade Count: (2)
  • Member
  • *
  • Posts: 71
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #2 on: March 14, 2010, 06:00:00 PM »
Sorry about the previous post. I was trying to do a link to another thread on here. If you go to the second page of this forum there is a thread about this very same topic.I'm gonna try this again.How is 308 brass reformed to 7mm-08 brass? .
Logged

Offline DEACONLLB

  • GBO Supporter
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 2458
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #3 on: March 14, 2010, 06:01:03 PM »
I was under the impression that 7mm08 was a 308 case sized to 7mm like 7-30 waters is 30-30 sized to 7mm or do I have my facts wrong?

Deaconllb
Logged
Korean war vet. NRA Member
Fourth fighter wing K14 Kimpo Korea 1952 Fourth but first, the mig killers.
533rd material ,air defense Oxnard AFB 1953-1955
Pastor of the  CBCG-Fellowship group Tulsa Oklahoma.

Offline mrjbloomington

  • Trade Count: (2)
  • Member
  • *
  • Posts: 71
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #4 on: March 14, 2010, 06:07:48 PM »
Yeah, it is. Sorry, I was trying to get a link to a previous thread on here. I'm having problems figuring it out. ??? Trial and error thing! just go to the second page and there is a whole trhead about this.  ;)
Logged

Offline bilmac

  • GBO Supporter
  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 3560
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #5 on: March 14, 2010, 06:08:37 PM »
You got it Deacon, Run it through a 7-08 die, and shoot it. I had trouble with a 7-08 rifle that wouldn't shoot and I tried everything. Finally since most of my brass was 308, I bought an outside neck turner. Didn't help.
Logged

Offline mrjbloomington

  • Trade Count: (2)
  • Member
  • *
  • Posts: 71
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #6 on: March 14, 2010, 06:13:10 PM »
 Let's try this maybe it'll work ://www.gboreloaded.com/forums/index.php/topic,201774.msg1099044705.html#msg1099044705.

Dang it, i'm gonna quit trying this until I git 'er figured out!!
Logged

Offline yooper77

  • Trade Count: (33)
  • Senior Member
  • *****
  • Posts: 1746
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #7 on: March 14, 2010, 06:55:29 PM »
Quote from: DEACONLLB on March 14, 2010, 04:58:57 PM
If I get some 308 brass how do I form it to 7mm08, Do i just size it in a 7mm08 die,  what is the process?

All I use for my 7mm-08 Remington ammo is 308 Winchester brass, saves me lots of money.

Yes you got is perfect, just full length size.  Always good to check the trim length, but most likely it will be shorter than the trim length for 7mm-08 Remington.

yooper77
Logged

Offline LaOtto222

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3828
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #8 on: March 15, 2010, 07:34:04 AM »
I do not get where everyone thinks that 308 brass is so much cheaper than 7-08 brass. Presently, there is only $5 difference between the cost of new 308 ($40) and new 7-08 ($45) brass per hundred. Unless you have 308 brass that is new given to you (lucky you) or you have known once fired brass for free or extremely cheap, I just do not get it. Why save $5 (5 cents per piece) and end up with a head stamp that is not correct, the hassle of full length sizing and shorter case life. I do not full length size new brass, because it just works the brass once more than it needs to be. I definitely would not use brass of unknown origin or unknown number of firings. I always just neck size brass as much as possible and consider the first firing to a forming load so full length sizing just squeezes it down once more. But that is me, you are always free to do what ever you want. Good Shooting and Good Luck
Logged
Great men have vision and resolve to make dreams come true.

Offline PA-Joe

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 980
Re: forming 308 brass to 7mm08?
« Reply #9 on: March 15, 2010, 08:33:38 AM »
Because 308 range fired brass is free and there lots of it around.
Logged

Offline LaOtto222

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3828
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #10 on: March 15, 2010, 10:21:40 AM »
Like I said if it is free, then have at it. I do not get any range brass and not sure I would use it if I could - but that is me.
Logged
Great men have vision and resolve to make dreams come true.

Offline bilmac

  • GBO Supporter
  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 3560
  • Gender: Male
Re: forming 308 brass to 7mm08?
« Reply #11 on: March 15, 2010, 06:59:40 PM »
I was on a National Guard rifle team for awhile. Lots of match brass . I think that is about the best brass you can get. Actually I bought the 7-08 because I had all of this good brass.
Logged
Pages: [1]   Go Up
« previous next »