« previous next »
Pages: [1]   Go Down

Author Topic: Rebarreling Montana 1999 action?  (Read 533 times)

0 Members and 1 Guest are viewing this topic.

Offline greer

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 180
Rebarreling Montana 1999 action?
« on: March 25, 2010, 06:42:23 AM »
 Do any of you fellers know if the Montana 1999 action requires the barrel to have a clearance cut for the extractor? I believe it is patterned after the pre-64 M70 which I think does have a cut. I have rebarreled  several Model 700's and a Ruger or two but have no experience with this action. Is locating and doing the cut a tricky job?       Thanks alot. greer
Logged

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: Rebarreling Montana 1999 action?
« Reply #1 on: March 25, 2010, 08:39:27 AM »
I've not done one of these so can't help.. Anybody done one?
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline trotterlg

  • GBO Supporter
  • Trade Count: (36)
  • Senior Member
  • *****
  • Posts: 3978
  • Gender: Male
Re: Rebarreling Montana 1999 action?
« Reply #2 on: March 25, 2010, 08:21:30 PM »
I will guess you don't have the origional barrel to look at.  It probably would also depend on if you are chambering the barrel for a rimmed or rimless cartridge and what the origional was.  Larry
Logged
A gun is just like a parachute, if you ever really need one, nothing else will do.

Offline greer

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 180
Re: Rebarreling Montana 1999 action?
« Reply #3 on: March 26, 2010, 06:58:16 AM »
 The fellow bought the action only and said he had a fully chambered Shilen barrel that needs the shoulder set back. He didn't know anything about an extractor cut. I'll call him and get a few more details. I guess I could call the Montana folks.  Thanks alot for the reply. greer
Logged

Offline trotterlg

  • GBO Supporter
  • Trade Count: (36)
  • Senior Member
  • *****
  • Posts: 3978
  • Gender: Male
Re: Rebarreling Montana 1999 action?
« Reply #4 on: March 26, 2010, 10:56:27 AM »
If it is for a rimmed cartridge then it most likely will need an extractor cut of some sort.  If it is rimless I would guess it would not be needed.  A look at the bolt head will probably tell you what you need to do with it.  Larry
Logged
A gun is just like a parachute, if you ever really need one, nothing else will do.

Offline Rangr44

  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 2158
Re: Rebarreling Montana 1999 action?
« Reply #5 on: March 29, 2010, 03:54:50 AM »
FWIW, an inner collar ring on the Montana 1999 action, Mauser-derived, includes the extractor cut to eliminate the need for cone breeching or an extractor cut in the barrel extension.

.
Logged
There's a Place for All God's Creatures - Right Next to the Potatoes & Gravy ! !

Offline greer

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 180
Re: Rebarreling Montana 1999 action?
« Reply #6 on: March 29, 2010, 05:38:07 AM »
 Thanks for the reply. I passed on the job as I wasn't sure about what it involved. Sounds like it would have been a pretty much routine deal.  Thanks again for the help.  greer
Logged
Pages: [1]   Go Up
« previous next »