Author Topic: New Encore (Read 442 times)

NHANG · « **on:** November 29, 2003, 02:32:25 PM »

I just ordered a new Encore today and the barrel I've decided to go with is the blue 15" .243. After reading many postings, I'm still unsure what Burris scope is best suited for this gun; 3x12 or 2x7. I'd also like some advice on what rings and base to purchase.

Just for some gee wiz info. TC offers one gun at cost per year to NH Hunter Safety Instructors. The barrel, frame, and grip will cost me $398. Good deal from TC!

Thanks for your help.

doc-and · « **Reply #1 on:** November 29, 2003, 02:51:29 PM »

I have both Burris scopes, but need more info on your proposed use to advise. Either scope will do a great job. As for base/rings, I like the weaver base with Burris Signature rings. With these rings there is little or no maring of the scope and they hold the scope well.

Just my 2 cents

doc-and

KYODE · « **Reply #2 on:** November 29, 2003, 05:45:41 PM »

for the encore, i prefer a burris dual dovetail base, and signature dual dovetail rings with inserts. + what doc-and said :-)
those two scopes are top notch choices, in my opinion. i have and use both.
now, like doc said, it depends on the majority of it's intended use. the 2x7 would be my preference in the deer woods, or shots at closer ranges. it has a very wide field of view on 2x(more than most, if not all out there). 21'wide @100yards. it's nice in timber,etc. and 7x will suffice for most target work.
the 3x12 model is great also, but the field of view is smaller. about 14' wide @100yards on 3x. it is usable, but is a definate handicap compared to the 2x7 model. it's field of view on 3x still compares with almost all other handgun scopes on the low x's. the 12x power is super for long range shots, and shooting tight groups.
the 2x7 model comes with, or without an adjustable objective. all the 3x12's have an adjustable objective, and a model that has target turrets. a balistic plex reticle is available also, but i havn't used one to comment on.
great buy! :agree:

NHANG · « **Reply #3 on:** November 30, 2003, 02:48:52 AM »

I plan to use the gun for hunting deer and coyote. The environment I'll be hunting varies from open hardwoods to heavy softwoods so I estimate that the longest shots maybe 175 yards. My Dad and I also do alot of target shooting at ranges up to 200 yards. He's actually purchasing an Encore rifle the same time I buy this. I'm not sure yet as to what caliber he'll be getting but there is always a "competition" at the range between us. Being a pistol vs. a rifle, I'll really have to do my part.

Back to the rings and bases, I've read that some mount 2 rings and others 3. What is ideal for a .243? The Encore comes drilled and tapped for a scope correct? At what torque do you tighten the mounting screws and do you put anything on the threads; i.e. blue Loctite?

Thanks for all your help.

doc-and · « **Reply #4 on:** November 30, 2003, 05:22:59 AM »

NHANG,

The .243 is what I would consider a mild recoiling caliber, and two rings should be sufficient to secure the scope. Encore barrels, (factory) do come drilled & tapped for scope mounting. With the 15inch barrel you will need to remove the rear sight, which is quite simple. Under the sight base is the remaining mounting holes (total of 4). I use red loctite when mounting scope bases, and use it sparingly!!

Also before using the loctite, CHECK your screw lengths, by this position the base and insert one screw at a time to make sure that they don't bottom out before the base is secure. Remove the previous screw and go to the next screw/hole combination until all holes/screws are checked. Every one in a while a shallow hole or long screw will slip by and cause a problem. With the base mounted and the rings installed you should be good to go.

Good luck. Continue to read this forum, there is a lot of good information here for the reading.

doc-and