« previous next »
Pages: [1]   Go Down

Author Topic: Will a H&R 1871 Stock fit 158 Topper Frame?  (Read 1849 times)

0 Members and 1 Guest are viewing this topic.

Offline kf4ocv

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 141
  • Gender: Male
Will a H&R 1871 Stock fit 158 Topper Frame?
« on: October 05, 2010, 12:26:01 PM »
I am thinking of redoing an old 158 Topper Shot Gun I acquired recently.  The stock has 2 DEEP dents in it.  I know I could use wood filler but what are the chances I could get a new one instead.  I have looked @ gun stocks inc but they dont do the forearms for 158 Toppers.  (my gun has the snap on fore arm)
Logged
Chris

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #1 on: October 05, 2010, 03:03:51 PM »
Maybe, maybe not, the only way to know is try it, the forend won't work without modification since they're all screw on. I had an early 70's M158, a modern stock didn't fit it well, the angle of the stock bolt was slightly different.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline kf4ocv

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 141
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #2 on: October 05, 2010, 03:24:00 PM »
I will try to get some pics on here.  Someone refinished and did not remove the frame from the stock and wore off the blueing where they mate.
Logged
Chris

Offline kf4ocv

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 141
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #3 on: October 05, 2010, 03:27:09 PM »
  Does anybody make reproduction stocks for these.  I already tried Gun Stock inc they only make stocks for current production.
Logged
Chris

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #4 on: October 05, 2010, 03:40:20 PM »
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline godogz

  • Trade Count: (4)
  • Avid Poster
  • **
  • Posts: 136
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #5 on: October 05, 2010, 04:05:44 PM »
Are these parts for the 158 or all H&R?

ok, I see the link at the top of the drawing - 158
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #6 on: October 05, 2010, 05:13:36 PM »
Not necessarily, they pretty much put all the H&R single shot common parts in one spot.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline kf4ocv

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 141
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #7 on: October 08, 2010, 06:27:06 AM »
if they put all the single shot parts together,  there is no to know if the part will fit Right?    Other than that it looks like what I am looking for.
Logged
Chris

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #8 on: October 08, 2010, 02:27:21 PM »
One other thought for you would be that you might be able to steam out the dents.  Don't know how bad they are, but if you steam the wood it will often raise the grain enough to re-sand down to level.  Just another idea.  ;)
Logged
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Will a H&R 1871 Stock fit 158 Topper Frame?
« Reply #9 on: October 08, 2010, 03:48:59 PM »
Quote from: kf4ocv on October 08, 2010, 06:27:06 AM
if they put all the single shot parts together,  there is no to know if the part will fit Right?    Other than that it looks like what I am looking for.

They do list serial number ranges for some parts, other than description, that's about it.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain
Pages: [1]   Go Up
« previous next »