« previous next »
Pages: [1]   Go Down

Author Topic: Barrel with shim vs value  (Read 487 times)

0 Members and 1 Guest are viewing this topic.

Offline Elkoholic

  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 148
  • Gender: Male
Barrel with shim vs value
« on: October 29, 2010, 04:03:23 PM »
Hey guys,

So I purchased a 223 bull barrel about a year ago of the GBO classifieds.
It didn't fit my SB-2 frame well and I ended up putting in a shim per
instructions on this site.  Locks up great and shoots sub-moa.

My question is, if I were to ever sell this barrel in the future, because
it has been shimmed, will that effect it's selling price?

Thanks!!!
Mike
Logged
Current Handi's: 17 HMR, 270 Ultra Comp, 223 Bull Barrel.
Barrel wish List: 22 Hornet, 7-08, 30-30, 357 Mag, 45 Long Colt for starters.   Oh, and 35 Whelen too!
Donations gladly accepted!!

Offline 26-t

  • Retired
  • GBO Supporter
  • Trade Count: (21)
  • Contributor
  • *****
  • Posts: 307
  • Gender: Male
  • Father and Son At Bonneville SpeedWeek 07
Re: Barrel with shim vs value
« Reply #1 on: October 29, 2010, 04:08:48 PM »
Most of the time they will need to be shimmed ,so IMHO it makes no difference in the price. (Fitting dose) how ever will matter,i.e. filing on lug . 26-t
Logged

Offline necchi

  • GBO Supporter
  • Trade Count: (40)
  • Senior Member
  • *****
  • Posts: 1842
  • Gender: Male
Re: Barrel with shim vs value
« Reply #2 on: October 29, 2010, 04:29:20 PM »
Depends on the buyer, some guy's are fussy and they can pass on it, others might snap it up??
If all you did was add a shim, removing the shim will put it back to original right?
When/if you sell, simply mention it's history like you have here, list for the going rate and adjust from there depending on how great your need is to sell.

I have a bull in 1-12, it's fun ta shoot !  ;D
Logged
found elsewhere

Offline topper88

  • Trade Count: (5)
  • Member
  • *
  • Posts: 65
Re: Barrel with shim vs value
« Reply #3 on: October 30, 2010, 02:51:37 AM »
There is a hight tensile strength tape made by 3M, it's light olive in color.  I have it for masking areas on my boat prior to gel coating.  When pulling it off I was amazed how strong it was for it's thickness and I thought to try it on my Handi's.  So far it has surpassed my expectations.  The beauty is it can be peeled off easily.  I only shoot lead up to 24K PSI pressures and it works beautifully for my application. 

I also noticed an aluminum foil tape for doing ductwork in Wal-mart. I didn't buy any but that should work for some. 

Even if a lug is epoxy shimmed it can be carefully filed down to fit.
Logged

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: Barrel with shim vs value
« Reply #4 on: October 30, 2010, 06:09:16 AM »
I think the real determining factor(s) here are, as said, when the shim comes off is the lug 'as original'
and/or 'is the work decently done'. There is a great difference in workmanship and the way some people go at gun parts with files and grinders quickly can make a 'sow's ear'.
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline moorepower

  • Trade Count: (14)
  • A Real Regular
  • ****
  • Posts: 518
Re: Barrel with shim vs value
« Reply #5 on: October 30, 2010, 07:21:46 AM »
I myself, would pass on a shimmed barrel. Yes they can be made to work well, but I would always wonder the history of the barrel. I have 4 frames and they are all really short, so every barrel I have fit, I have to remove a quite a bit of material to fit them, which is fine by me because I like to true the back of the barrel and take the material off the latch, not the lug.
Logged
Pages: [1]   Go Up
« previous next »