« previous next »
Pages: [1]   Go Down

Author Topic: Forend Hanger Bar  (Read 1007 times)

0 Members and 1 Guest are viewing this topic.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Forend Hanger Bar
« on: February 16, 2011, 02:23:14 PM »
I finished the Handi hanger bar today, it took quite a bit less time than the dovetail version I did on the Wizard barrel, I put this one on the 260 Rem Superlight barrel hoping it will benefit the most from more free floated barrel although it's not much, but I'll be able to compare the two mounting methods since I didn't remove the forend stud, there's a bit more space between barrel and forend with the mount in place, so the stud doesn't touch.

The barrel  is .745" straight at this point, so all I did was run a ¾" (.746") end mill down the side of a short length of ½" square 6061, that fits the contour of the barrel real good, then drilled it in two positions, used a center finder to locate the center of the barrel, then drilled and tapped one 8-40 hole in the barrel then anchored the mount with one screw and used the other hole position to locate the other hole in the barrel so they matched the holes in the mount.

Range trip when the weather improves.  ::)

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Slowhanddd

  • GBO Supporter
  • Trade Count: (43)
  • A Real Regular
  • *****
  • Posts: 691
  • Gender: Male
Re: Forend Hanger Bar
« Reply #1 on: February 16, 2011, 03:09:07 PM »
Things to do in rainy weather.Looks good there Tim.
Logged
Life is not about how fast you run, or how high you climb, but how well
you bounce

Offline Littlepage

  • Trade Count: (0)
  • Member
  • *
  • Posts: 72
  • Gender: Male
Re: Forend Hanger Bar
« Reply #2 on: February 16, 2011, 04:24:41 PM »
Is the 260 Rem a custom barrel?   My wife's stepfather has only good things to say about the 260 rem. 
Logged

Offline Slufoot

  • Trade Count: (21)
  • Senior Member
  • *****
  • Posts: 1004
Re: Forend Hanger Bar
« Reply #3 on: February 16, 2011, 04:40:01 PM »
Hey Tim, I believe this could be something good! Looking forward to a range report and comparison of before and after.

GOOD SHOOTING!
Slufoot
Logged

Offline mechanic

  • GBO Supporter
  • Trade Count: (32)
  • Senior Member
  • *****
  • Posts: 5112
  • Gender: Male
Re: Forend Hanger Bar
« Reply #4 on: February 16, 2011, 05:06:12 PM »
Quick, looks simple and effective.  If it works, you can open shop.......IMO the biggest problem with single shots is that pesky forend.....

Ben
Logged
Molon Labe, (King Leonidas of the Spartan Army)

Offline Dinny

  • Moderators
  • Trade Count: (268)
  • Senior Member
  • *****
  • Posts: 5524
  • Gender: Male
  • "Medics Save"
Re: Forend Hanger Bar
« Reply #5 on: February 16, 2011, 05:45:32 PM »
Tim,
  I think you have out-done yourself again! Is there any room to glass bed it to the forend? Any need to? I am patiently awaiting the range report results.... :P

Thanks, Dinny
Logged
Handi Family: 357 Max, 45 LC, 45-70, 300 BLK, 50 cal Huntsman, and 348 Win.

"If there must be trouble, let it be in my day that my child may have peace"
Thomas Paine

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Forend Hanger Bar
« Reply #6 on: February 16, 2011, 06:15:32 PM »
Thanks guys, this definitely was a good way to deal with cabin fever!!  ;D  I made this one for a synthetic forend, but it could be made a little different for a wood forend with no problem by using thinner material for the longer piece, .375" instead of .500" material, it could be bedded too.

The 260 Rem barrel is a rebored 243 barrel.

Tim

Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: Forend Hanger Bar
« Reply #7 on: February 17, 2011, 07:25:13 AM »
Well Done  ;)!
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline carbineman

  • GBO Supporter
  • Trade Count: (58)
  • Senior Member
  • *****
  • Posts: 1322
Re: Forend Hanger Bar
« Reply #8 on: February 17, 2011, 10:25:31 AM »
Tim, You do really nice work. I'll be looking for your range report as well. Seems one has to be handy to work on a handi.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Forend Hanger Bar
« Reply #9 on: February 17, 2011, 10:26:28 AM »
Or waaaay too much free time!!!  ;D ;D ;D

Thanks guys.  ;)

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline JimG

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 419
Re: Forend Hanger Bar
« Reply #10 on: February 17, 2011, 11:39:20 AM »
What's the purpose of this hanger bar? Looks neat but not sure why it's needed?
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Forend Hanger Bar
« Reply #11 on: February 17, 2011, 01:15:47 PM »
To free float more of the barrel, it also eliminates any contact between the frame and forend, the forend is attached only to the barrel, it doesn't touch the frame at all.

Tim

http://www.strattoncustom.com/pages-main/category-7/forend-hanger-bars.html
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline AA080

  • Trade Count: (7)
  • Member
  • *
  • Posts: 44
Re: Forend Hanger Bar
« Reply #12 on: February 17, 2011, 01:22:29 PM »
Tim, when you open the action, won't the barrel be real wobbly without any contact?
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Forend Hanger Bar
« Reply #13 on: February 17, 2011, 01:25:49 PM »
Yup, but who cares if it shoots bug holes!!  8) Been shooting them that way for years, doesn't hurt a thing.  ;) Read number 5 of the Handi Basics 101 sticky.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline JimG

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 419
Re: Forend Hanger Bar
« Reply #14 on: February 17, 2011, 01:46:12 PM »
So how much space is between the plastic forend spacer and the frame when the forend is attatched?
Logged

Offline michstew

  • Trade Count: (0)
  • Member
  • *
  • Posts: 62
Re: Forend Hanger Bar
« Reply #15 on: February 17, 2011, 01:53:41 PM »
A blond hair, maybe a strawberry one. Tim you ARE THE WIZARD!!   michstew
Logged

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: Forend Hanger Bar
« Reply #16 on: February 17, 2011, 02:27:08 PM »
I think I would use a layer of VERY thin celophane tape at the forearm/frame contact and glass bed the forearm to tightly fit the hanger, with good back pressure to the tape while it sets.
Make sure you chamfer the edges of the hanger block if you do this so it can come apart without too much trouble later.
Even with no contact and a bit loose on opening the barrel wont fall off like they want to when you dont have a forearm on at all!
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Forend Hanger Bar
« Reply #17 on: February 17, 2011, 05:33:38 PM »
Quote from: JimG on February 17, 2011, 01:46:12 PM
So how much space is between the plastic forend spacer and the frame when the forend is attatched?

About .005", enough to pass paper thru.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain
Pages: [1]   Go Up
« previous next »