« previous next »
Pages: [1]   Go Down

Author Topic: 45-70 BC hunting loads  (Read 418 times)

0 Members and 1 Guest are viewing this topic.

Offline jimbobb55

  • GBO Supporter
  • Trade Count: (0)
  • Member
  • *****
  • Posts: 88
  • Gender: Male
45-70 BC hunting loads
« on: October 28, 2011, 09:31:48 AM »
Now that I have my BC back from H&R. I have two weeks till opening day of deer season. I want to use 405 Rem. over IMR 4198, Never used a 405, before and the gun has a new barrel and I don't have much time. I could use some ideas.
Logged

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: 45-70 BC hunting loads
« Reply #1 on: October 28, 2011, 11:59:05 AM »
Well Jimbob, I don't use H4198, but Hodgedon's load data for a 400 gr. should be a good starting point.  ;)
 
Cartridge:
 45-70 Government (Modern Rifles)*
Load Type:
 Rifle
Starting Loads
 
Maximum Loads
 
Bullet Weight (Gr.)
Manufacturer
Powder
Bullet Diam.
C.O.L.
Grs.
Vel. (ft/s)
Pressure
Grs.
Vel. (ft/s)
Pressure

400 GR. SPR JFP
Hodgdon
H4198
.458"
2.540"
48.0
1915
31,800 CUP
53.0
2108
49,100 CUP

I use Reloader7 as I have had nothing but stellar results from it and it's quite inexpensive here.  Using that I'd try about 45 gr. starting level w/ max at 49gr. and work up until good accuracy and comfortable.  You can go down as low as 35gr. for trap door level loads if you want some light ones too.  ;)
Logged
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: 45-70 BC hunting loads
« Reply #2 on: October 28, 2011, 12:03:13 PM »
And just to give you some confidence inspiring words, "it is really hard to make a load that does not work in a 45-70"!
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline jimbobb55

  • GBO Supporter
  • Trade Count: (0)
  • Member
  • *****
  • Posts: 88
  • Gender: Male
Re: 45-70 BC hunting loads
« Reply #3 on: October 28, 2011, 01:34:58 PM »
Thank you for da info. I started at 45gr. I'll let you know how it goes.
Logged

Offline Jimbo47

  • GBO Supporter
  • Trade Count: (25)
  • Senior Member
  • *****
  • Posts: 1304
  • Gender: Male
Re: 45-70 BC hunting loads
« Reply #4 on: October 28, 2011, 05:21:51 PM »
That 48 grains will loosen you dentures.
 
I use 30.3 grains of IMR 4198 under a 400 grain JSP Speer bullet.
 
Accurate and easy on the shoulder load.
 
Personally I don't care for a lot of recoil, and 1500 fps is about my max when it comes to big heavy bullets, but 1200 to 1500 fps. is plenty for deer using a 405 grain bullet.
Logged
My culled down Handi's are the 45-70, and then I have a few others to keep it company...357 Mag/Max. .45 LC/.454 Casull Carbine, .243 Ultra, and 20 gauge Tracker II.

Offline DaveW

  • Trade Count: (0)
  • Member
  • *
  • Posts: 22
Re: 45-70 BC hunting loads
« Reply #5 on: October 31, 2011, 01:12:30 AM »
I've killed two animals this year with 35 grn of IMR 4198 behind the 405 rem. A 200lb+ black bear and a whitetail doe. Complete pass through on both animals. They don't have to go fast or hurt your shoulder.
Logged
Pages: [1]   Go Up
« previous next »