« previous next »
Pages: [1]   Go Down

Author Topic: hand reaming for choke tubes and forcing cone  (Read 1094 times)

0 Members and 1 Guest are viewing this topic.

Offline cudatruck

  • Trade Count: (25)
  • A Real Regular
  • ****
  • Posts: 680
  • Gender: Male
hand reaming for choke tubes and forcing cone
« on: March 21, 2012, 01:56:46 PM »
have any of you rented the reamer/tap for choke tubes or forcing cone reamer from 4D or another source and done these jobs by hand or another method without a lathe? Really want to try this but am worried about not being able to get it done.
Logged

Offline jeepmann1948

  • GBO Supporter
  • Trade Count: (67)
  • Senior Member
  • *****
  • Posts: 1422
  • Gender: Male
  • San Angelo, Texas
Re: hand reaming for choke tubes and forcing cone
« Reply #1 on: March 21, 2012, 02:04:28 PM »
An Old Fashioned Brace and bit works well for this project.Just be sure and NOT stop the handle in the same position or you will get chatter marks.Also be very liberal with the cutting oil.
Good Luck
George
Logged
"it ain't what you shoot em with......................
  it's where you hit em "

Offline Froghunter

  • GBO Supporter
  • Trade Count: (36)
  • Contributor
  • *****
  • Posts: 307
  • Gender: Male
  • .38 Special and .357 S&W Magnum Stuff
Re: hand reaming for choke tubes and forcing cone
« Reply #2 on: March 22, 2012, 02:13:49 PM »
Truck,
This may help and if you have ???? Please PM me.
http://www.gboreloaded.com/forums/index.php/topic,212222.msg1099134706.html#msg1099134706
Enjoy!
Froghunter
 
 
 
Logged
"Think Positive and Positive Things Will Happen"

"There's Only One Bore Size and That is .357....That's MHO"

Froghunter

Offline cudatruck

  • Trade Count: (25)
  • A Real Regular
  • ****
  • Posts: 680
  • Gender: Male
Re: hand reaming for choke tubes and forcing cone
« Reply #3 on: March 25, 2012, 08:00:34 AM »
ok  froghunter i read your thread looks very cool, but did you ream all those barrels by hand with tap wrench, brace and bit set up, cordless drill ? or did you put them on a lathe?
Logged

Offline bikerbeans

  • Trade Count: (168)
  • Senior Member
  • *****
  • Posts: 4070
  • Gender: Male
  • BANDIT - North American Snake Hound
Re: hand reaming for choke tubes and forcing cone
« Reply #4 on: March 25, 2012, 03:42:25 PM »
cuda,
 
call or email Fred at 4D and ask his opinion on using these reamers by hand.   
 
BB
Logged
RIP Tom: Tom Nolan, ( bikerbeans) passed away this afternoon (02-04-2021).

Why be difficult, when with a little extra effort you can be impossible?

Wife's Handis;  300 BLKOUT

MINE:  270W, 308x444, 44 Bodeen, 410 shorty rifled slug gun, 445 SuperMag Shikari, 45 ACP shorty,  45-70 Shikari, 45 Cal Smokeless MZ, 50cal 24" SS Sidekick, 50 cal 24" Huntsman, 50 cal 26" Huntsman, 50 cal 26" Sidekick, 50-70 Govt Shikari, Tracker II 20 ga shorty, 20 ga VR Pardner, 20ga USH, 12ga VR NWTF, 12ga Tracker II shorty WITHOUT scope, 12ga USH, 10 ga  Pardner Smoothbore slug gun & 24ga Profino Custom rifled slug gun.

Offline Froghunter

  • GBO Supporter
  • Trade Count: (36)
  • Contributor
  • *****
  • Posts: 307
  • Gender: Male
  • .38 Special and .357 S&W Magnum Stuff
Re: hand reaming for choke tubes and forcing cone
« Reply #5 on: March 31, 2012, 02:11:22 PM »
Yes.....By hand with a cresent wrench and a lot of oil. The forcing cone reamer has a close to bore size bushing at the bore end. The reamer I used for the choke removal was adjustable and I used it in steps to remove a little at a time and then mic'ed it. It was not hard to do or take long to do. H&R barrel metal is soft.
Froghunter
Logged
"Think Positive and Positive Things Will Happen"

"There's Only One Bore Size and That is .357....That's MHO"

Froghunter
Pages: [1]   Go Up
« previous next »