« previous next »
Pages: [1]   Go Down

Author Topic: lead bullet touching the rifling?  (Read 672 times)

0 Members and 1 Guest are viewing this topic.

Offline anweis

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 557
lead bullet touching the rifling?
« on: February 28, 2013, 09:34:46 AM »
Did i get this right? Seat jacketed bullets 0.010"-0.040" from rifling, but have lead gas sealed bullets touching the rifling? I am about to experiment with the lead non-jacketed bullets in a 7 x 57.
I have the Hornady COL seating gauge or whatever it's name. Thanks.     
Logged

Offline Ranch13

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1062
  • Gender: Male
    • Historic Shooting .com
Re: lead bullet touching the rifling?
« Reply #1 on: February 28, 2013, 10:36:58 AM »
There really is nothing set in stone. Each rifle with different bullets and loads is going to make up it's own mind whether it prefers the bullets seated to the lands or not. Type of bullet doesn't matter, some will shoot better seated out some won't.
Logged
In the 1920's "sheeple" was a term coined by the National Socialist Party in Germany to describe people that would not vote for Hitler. In the 1930's they held Hitler as the only one that would bring pride back to Germany and bring the budget and economy back.....

Offline hornady

  • Trade Count: (2)
  • Contributor
  • ***
  • Posts: 477
Re: lead bullet touching the rifling?
« Reply #2 on: March 01, 2013, 04:52:18 AM »
Ranch pretty much nailed it. I have two old 7X57 Mausers, a 91 and a 95. I shoot mainly my Lyman cast bullets in. The 91 shoots great with the recommended COL, from the Lyman cast book, the 95 I needed to set the bullet out a little. 
Logged

Offline wncchester

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3856
  • Gender: Male
Re: lead bullet touching the rifling?
« Reply #3 on: March 03, 2013, 03:07:01 PM »
"Did i get this right? Seat jacketed bullets 0.010"-0.040" from rifling, but have lead gas sealed bullets touching the rifling?"
 
You probably "got it right" but it's a lie.  I'm not sure what a 'lead gas sealed bullet' is but we would all like to posess the presumed 'secrets' of 'best' perfomance; tools, rifles, components, methods, etc.  Fact is, there are no such secrets or tools nor any preset 1-2-3 methods/steps = instant performance; experimentation is the only answer to finding your own best.
 
No one gives a "recommended" OAL for anything, what we see in the books is just what the book making team used in their own firearms and theirs isn't ours; experiment.
Logged
Common sense is an uncommon virtue

Offline gary0529

  • Trade Count: (0)
  • Member
  • *
  • Posts: 85
Re: lead bullet touching the rifling?
« Reply #4 on: March 05, 2013, 01:18:04 AM »
Maybe the OP means "gas checked" and does not know the term.

As to the question, the previous posters nailed it. There is no magic formula. Projectile hardness(high or low Brinell #), velocity, barrel condition, caliber and about 3000 other intangibles all go into determining an accurate and effective loading.

If you have not already been told, here it is again--Each gun is an entity unto itself" 
What works for me and mine may or may not be right for you.

Gary
Logged
Pages: [1]   Go Up
« previous next »