Author Topic: Polishing out barrel-bluing? Is there a technique?  (Read 834 times)

0 Members and 1 Guest are viewing this topic.

Offline Couger

  • Trade Count: (77)
  • Senior Member
  • *****
  • Posts: 1652
Polishing out barrel-bluing? Is there a technique?
« on: June 24, 2013, 08:54:28 AM »
 
Just wondering ...... :o
 
 
 
On my .45/70 barrel a couple inches back from the 26" muzzle, the finish appears marred like from leaning in a rifle rack for too long, and I'd like to polish it out to its original (medium) shine, if that is possible!!??
 
 
 
I've wondered if gun oil mixed with and extremely ffiiiiiinne abrasive would work?
 
Please , any suggestions?  ;)   8)

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #1 on: June 24, 2013, 09:02:07 AM »
Oil and #0000 superfine steel wool has always worked for me, I use it all the time when remounting scope rails or prep for touch-up. Their bluing is usually pretty thin tho, so beware, it may require rebluing.

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Couger

  • Trade Count: (77)
  • Senior Member
  • *****
  • Posts: 1652
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #2 on: June 24, 2013, 02:29:46 PM »
Quote from: quickdtoo
Oil and #0000 superfine steel wool has always worked for me, I use it all the time when remounting scope rails or prep for touch-up. Their bluing is usually pretty thin tho, so beware, it may require rebluing.
Tim

I've noticed that too about their bluing, but I'll try the #0000 and oil!
 
THANKS!  :)

Offline PineyCreek22

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 163
  • Gender: Male
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #3 on: June 24, 2013, 02:54:01 PM »
Tims advice is right on.  Anything else and you are through the blue and you are looking at a whole different ball game. PC
custom .357 mag monoblock, custom 30-30 Handi

Offline mcwoodduck

  • Trade Count: (11)
  • Senior Member
  • *****
  • Posts: 7983
  • Gender: Male
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #4 on: June 24, 2013, 03:39:42 PM »
I use Flitz to clean off rust spots and make hte bluing shine.
It is like a fiiine toothpaste.  I think a little finer than 000 steel wool. 
It will remove any and all color case hardneing so beware.   
A little flitz a clean wash cloth (I buy the bulk pack at costco and keep them in the garage for gun stuff)   will clean up most any gun and a little rubbing will not go through the blueing.
If you need to remove the bluing there is a polishing compound called Never Dull a little of the packing and it will cleanly remove any and all bluing and get the metal ready to be de greased and reblued with the cold bluing rub on. 

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #5 on: June 24, 2013, 03:42:45 PM »
I just shoot it.  If it's accurate, leave it be.  ;)
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.


Offline theratdog

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 405
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #6 on: June 24, 2013, 06:56:28 PM »
pretty guns shoot better don't they :o

Offline Bugflipper

  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 1849
  • Gender: Male
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #7 on: June 24, 2013, 07:47:44 PM »
I know you just wanted medium but if a fellow wanted fine then red shop rags will take out the tiny scratches 0000 leaves. If a fellow wanted to keep going after that automotive polishing glaze will buff out the tiny scratched the shop rag left.
Molon labe

Offline nanuk-O-dah-Nort

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 701
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #8 on: June 25, 2013, 06:25:32 AM »
pretty guns shoot better don't they :o

I find the opposite is true

the Pretty ones are all show and no go...

the Ugly ones really put out, cause every "Hunt" might be their last!

Offline Couger

  • Trade Count: (77)
  • Senior Member
  • *****
  • Posts: 1652
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #9 on: June 26, 2013, 01:27:45 PM »
 
Thanks everyone!
 
Great comments one and all!  :)

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: Polishing out barrel-bluing? Is there a technique?
« Reply #10 on: June 28, 2013, 07:22:39 AM »
Rule of Thumb:
Until YOU know what to do to match, you dont know what to do.
Or, to put it another way:
Proceed with caution in an inconspicuous area.

"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974