Author Topic: m77 mk1 trigger adjustment (Read 1810 times)

300wsm:-) · « **on:** November 06, 2004, 08:05:06 AM »

i have the old style m77 w/ tang safety just wonder how to adjust the trigger pull. i havedone it on my mod 70 300wsm but the ruger i need some advice thanks

gunnut69 · « **Reply #1 on:** November 10, 2004, 09:04:32 AM »

I have included a link below to an exploded drawing of the M77 MKI. The screws that adjust the trigger are D-22, D-43, and D-44. The screw D-22 adjusts the amount of engagement of the sear/trigger. Adjusting this is dangerous as if too little engagement is provided the surfaces may chip or the rifle be liable to be jarred into firing. The screw D-43 adjusts the weight of the trigger pull and is limited in that by the strength of the spring installed as D-49. Turning this screw out will lower the spring tension required to be overcome to release the striker. If the pull weight can't be brought down to where you wish it this spring will need to be replaced by one made from lighter wire but which is still as long as the factory unit. This insures the trigger will reset and will not be bounced off engagement by the weight of the trigger when the rifle's butt is bounced on the floor. Screw D-44 adjusts the overtravel of the trigger. This is the amount the trigger moves after the sear releases. Adjust by tightening until the trigger won't release at all then slowly unscrew until the sear drops. Give the screw another 1/4 to 1/8 turn and lock. Always test the rifle for safety by bouncing the butt on a hard surface firmly. Also rapidly and briskly operate the bolt. The action MUST stay cocked or the trigger must be readjusted until it will. As a rule the trigger pull weight should not go below about 3 pounds in a hunting rifle. After all adjustments are confirmed as OK the adjustment screws should be locktited to prevent the adjustments from changing. The WARNING-- asjusting the trigger on any rifle using these or any directions entails some danger. If you choose to do this the danger and the responsibilty for it is entirely yours..

scratcherky · « **Reply #2 on:** November 10, 2004, 12:03:07 PM »

Gunnut
Would you try to repost the link to the exploded view of the MK 77 trigger?
Thanks,
Don

gunnut69 · « **Reply #3 on:** November 10, 2004, 04:01:36 PM »

WHOOPS!!! Forgot the link....must CRS again...maybe still!!

here's the link

http://stevespages.com/ipb-ruger-77.html

Cuz · « **Reply #4 on:** November 11, 2004, 08:12:54 AM »

Perhaps one of you gentlemen maybe able to help me??
I mounted a scope on my M77 in .257 Roberts and had to remove the rear sight because of the 50mm barrel on the scope. WHERE may I acquire slave screws to put in the tapping holes of the rear sight??

thanks, for your help

Cuz

gunnut69 · « **Reply #5 on:** November 11, 2004, 07:15:21 PM »

Any local gunshop will have them as will a local gunsmith. They are likely 6x48, unless the rifle was modified at some point. Brownells also sells them. Most hardware stores have plug screws but not the correct size. A local gunshop(usually not WalMart) should be able to assist...

Cuz · « **Reply #6 on:** November 12, 2004, 06:59:49 AM »

Thanks, the local gunshop could not 'find' any that fit.

I have been in touch with Brownell's and should have the screws by next week.

Cuz

gunnut69 · « **Reply #7 on:** November 12, 2004, 12:16:37 PM »

Most shops here abouts mount scopes free and the plug screws, unless the sights are also removed are thrown in a box. Almost all sight screws are 6x48..just what you need.. They can be the cheapest advertisement a shop can have...

Cuz · « **Reply #8 on:** November 15, 2004, 05:56:51 AM »

Well, have not found any as of yet. These screws are 8X36, according to the spec sheet and Brownell's does not carry that size. Anyone know of a source for slave (set) screws in 8X36 blued?? My local gunshops could not match the tapping, 8X40 was the closest, but they did not have 8X36 either.

Help, I need two 8X36 slave screws.

Cuz

gunnut69 · « **Reply #9 on:** November 15, 2004, 07:45:14 AM »

Sir

Take one of the screws you removed to take the rear sight off with you and go to a local machine shop. They will tell you the size and most likely will have them in house. 8x36 is aa most unusual size indeed. You may also consider a call the Rugers Customer service number. They use these plug screws on those m77's sold with rings only...