Author Topic: Best .35 cal for Encore pistol  (Read 2352 times)

0 Members and 1 Guest are viewing this topic.

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« on: May 12, 2005, 05:23:35 AM »
I'm going to purchase a .35 caliber barrel for my Encore in the near future.  I shoot a .357 Max in my Contender, it's my favorite barrel for that in pistol form.  I shoot a .35 Whelen AI in a rifle also, so I have the Redding three die set for that (FL size, Neck size, and bullet seater).  

I'm looking for a 200 yard thumper and have narrowed my choices to the .350 Remington Mag, .35 Whelen AI, and the .35/284 wildcat, with the possibility of a .358 Winchester still in consideration.  I know I can get a .375 JDJ barrel and that is also up for consideration, but I like the idea of the variety of bullets in .35 that should work at my velocity levels.  The Whelen AI or standard is a possibility as I already have the dies, but I was looking at the resale poetential should I decide I don't like it, which leans against the Whelen AI and the .35/284 (I shoot a .284 in an XP-100 so I've got plenty of cartridge cases available for that).  Anybody have any practical experience with the .350 Rem Mag in a short barrel, particularly the Encore or the original Remington carbines?  I looking to see what I'll gain in real world ballistics over the .358 Winchester.  I'm pretty well set on a 15" barrel and would like to avoid a muzzle brake, although I know it made a huge difference on my .284 Win XP-100.  The .350 Rem Mag makes the most sense financially because it can simply be ordered from the TC custom shop for a very reasonable rate with readily available dies and brass, the same could be said for the .358 Win for the most part.

What do you think?

Offline jhalcott

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1869
Best .35 cal for Encore pistol
« Reply #1 on: May 12, 2005, 07:15:56 AM »
I have a 358jdj contender and a 35 whelen rifle.I HAD a 358win lever gun(savage/18" barrel).I'm not sure how available 350 mag brass is, so unless I had a supply I'd pass on that round.I was getting 2500+fps from the 35 win round with some handloads/180 Hornady's.The 358jdj gets almost 2300 fps from a 14" barrel,same bullet. This round MIGHT be able to gain some from the Encore,as I load it for accuracy not speed. As for the '06 length cases in a 15" barrel, you'd need to load faster powders to get a complete burn. I'm not sure you'd actually gain much over the 358Win. I do know the 358jdj will kill a deer at 200 yards IF you do your part!

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #2 on: May 12, 2005, 07:44:52 AM »
jhalcott,
thanks for the input.

The .350 Rem Mag brass is readily available, Remington just re-released the round in their new M673 rifle in the last year or two, same for the 6.5 Rem Mag which was it's sister cartridge in the original carbines.

The case capacity is very similar to a 30-06 casing, and the info on the powder is interesting.  I found in my .284 Win, with case capacity similar to a 30-06 casing, that it was still faster than a 7mm-08 by a bit.  That's where my concern comes into play, will I be burning a bunch of extra powder and having extra recoil and noise with the '06 class casings for a small gain in real velocity?  I'm leaning towards the heavier bullets in the 225-250gr range for the bulk of what I want to do with this pistol, same bullets I shoot in the .35 Whelen AI rifle.  I would think, and I may well be way off here, that with a case similar in capacity to the .284, but with a much greater expansion ration as a result of the larger bore size, that the .35 caliber should be more efficient...ie closer to rifle velocities in proportion to the .284 in a 15" vs. 24" scenario.  The .284 seem to give up about 300fps +/- to a 22" rifle.

Offline JOE MACK

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 229
.35 caliber Encore
« Reply #3 on: May 12, 2005, 10:11:19 PM »
Whelenman,

I think the .350 Remington magnum would really be a bear in the Encore pistol. I use the case necked up to .411 (.41Whammy) and it's a real handful. I think a readily available factory-loaded cartridge with a little less powder capacity might be the thing. The .358 Winchester by virtue of its shorter powder column might be more efficient. I believe brass for the .356Winchester is available also. I like rimmed cases for my contenders and Encores. I've got a .307Winchester instead of the rimless .308. You might look into a .35WSM if someone will chamber it. Just some thoughts on the subject. After all, you asked. :grin:
JOE MACK aka Brian aka .41FAN

HAVE MORE FUN AND GET THE JOB DONE WITH A .41

Offline EdK

  • Trade Count: (2)
  • Contributor
  • ***
  • Posts: 499
Best .35 cal for Encore pistol
« Reply #4 on: May 13, 2005, 02:09:04 AM »
Of course I don't know how much power you'll be needing for the intended application however I really think the rimmed 356 Win would be a great fit for an Encore. Even though I'm a contender guy I have 8 barrels and not one of them is rimless. For 35 cal I went to the length to get a rim cut for my 35 Remington barrel so I could use rimmed Krag brass!

Offline jhalcott

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1869
Best .35 cal for Encore pistol
« Reply #5 on: May 13, 2005, 08:43:32 AM »
What are you REAL plans for this gun? I know a guy that had an Encore chambered to 416 Rem. He has 15/16 rounds from the original box setting in his safe.! I do NOT shoot my 358jdj or the 45-70 very much. I can't take the recoil any more.
   You can NOT get high velocity with out high pressure.This means lots of powder.BUT,you only have so much barrel to burn it in.The 358 win uses 41 grains of imr 3031 to get 2200 fps in a 22" barrel,250 gr bullet.The 350RM gets 2400 fps in an 18.5"barrel and uses 51 grains of 3031.NOW ,the 35 rem gets 2000 fps from only 36 grains of 3031 and a 20" barrel.This using a 200 grain bullet(the 250 grain is too stout for the 35 rem).

Offline Big Gun

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 120
Best .35 cal for Encore pistol
« Reply #6 on: May 14, 2005, 04:04:40 AM »
I was looking for a 35 cal Encore a while back and eventually settled on my first wildcat chambering - the 35-06 JDJ.  I just loaded up some test rounds last night.  The round is basically a 35 Whelen AI - improved some more, so you can start with 35 Whelen brass.  You will have plenty of power, and good resale value as JDJ barrels tend to hold their value.
Contenderize 'Em

Offline IKE

  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 132
  • Gender: Male
Best .35 cal for Encore pistol
« Reply #7 on: May 15, 2005, 01:13:16 AM »
I've been playing around with a blue 17" (counting brake) SSK Encore barrel chambered in 35 Whelen for a few weeks now and really like it.

Out of ten pet loads tested so far using Varget and IMR 4895 under a Hornady 180gr bullet, 55.0grs of Varget is the best load thus far with a five round group measuring a tad over one inch with each hole cutting another.

Ike
"To be one, ask one."

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #8 on: May 15, 2005, 07:12:59 AM »
Ike,
did you have an opportunity to shoot any of those loads over a chronograph?  I'd be very interested to see what velocity levels you are getting from the handgun tube.  Being as that I have the dies already, and a rifle chambered for it, I could just send a dummy round to OTT and go that route.

Offline IKE

  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 132
  • Gender: Male
Best .35 cal for Encore pistol
« Reply #9 on: May 15, 2005, 11:51:31 AM »
I haven't run them across a chrony, I don't own one.

Not that this is any indication of velocity but we've got a 3" thick steel gong at 200 yds. and with the above load the bullet put a dimple in the gong the dia. of a mans middle finger nail and deep enough to where you could rest a golf ball in the dimple, if the gong was horizontal, and it wouldn't have rolled off.......I was impressed.

In my opinion you've already got the dies on hand for your "200 yd. thumper", just have OTT make you either a 35 Whelen or the Ackley Improved version and never look back.

Ike
"To be one, ask one."

Offline Jay HHI6818

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 306
Best .35 cal for Encore pistol
« Reply #10 on: May 17, 2005, 05:01:39 AM »
I have a SSK 35-06 JDJ which is 11 inches long subtracting the brake. I have chronographed the Nosler 225 BT's @ 2266 FPS and was 2.o grains off max load.

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #11 on: May 17, 2005, 07:03:01 AM »
Jay,
thanks for the velocity info.  I too am looking at that chambering, likely in a 15" barrel, plus the brake.  Does SSK give out loading data for the chambering?  Have you tried any 250gr bullets?  How was the case forming?  From the pictures I've seen of the round it looks like it might be best to neck expand some Whelen brass to .375 and then run it through the full length size die, or buy some of the 30-06 cylinder brass from z-hat and just size it...shoulder looks awful sharp for the cylinder brass though...wouldn't want to ruin too many at $1/piece.

The waters have become further muddied with possibility of a .376 Steyr, but I'm still leaning towards the 35 cal.  I've got a good supply of bullets, moulds, sizer dies, etc for .35 cal.

Offline Big Gun

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 120
Best .35 cal for Encore pistol
« Reply #12 on: May 17, 2005, 02:57:41 PM »
SSK supplies data and instructions with the barrel / dies, as far as I know they are the only supplier of the dies.  I loaded up some fire forming test rounds for my 35-06 JDJ over the weekend, have not fired any yet though.  I started with 35 Whelen brass and then seated the bullet out so it just barely chambered in the Encore - the bullet hard against the rifling, as instructed on in info that came with the barrel from SSK.  I tried to use som 200 grain bullets but they were not long enough, I ended up using 250 grainers to make it work right.
Contenderize 'Em

Offline Jay HHI6818

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 306
Best .35 cal for Encore pistol
« Reply #13 on: May 18, 2005, 03:42:46 PM »
SSK supplies reloading data. I used IMI 30-06 brass and all you have to do is run it into the full length sizer die that has a tapered expander in it. I loaded the Hornday 250 gr Spire points for the fire form load as it was the only bullet long enough to touch the rifling. Didn't chronograph the 250's.
If you like the 375 caliber look at the 375-06 JDJ. Been told its a real handcannon!!!

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #14 on: May 20, 2005, 05:46:35 PM »
Thanks all for the input.  It looks like it's going to be the 35-06JDJ with a muzzle brake.

Is there any good design WOOD grip that is suitable for the recoil this will generate?  I've got the factory rubber grip, but I'm looking for a nice wood handle on this piece.

Offline haroldclark

  • Trade Count: (13)
  • Contributor
  • ***
  • Posts: 460
35 Calibers are the greatest.
« Reply #15 on: May 21, 2005, 12:23:35 PM »
This conversation sparked my interest since I like the 35 caliber, but I don't have the gonads(balls) to play where you guys are going.  I have researched the 35 calibers extensively for an Encore barrel and came to a conclusion that my 308 Winchester is more than adequate.  However, I still lust for a 35 caliber.  I traded my 357 Maxi barrel to Gene Gray for the 308.  It was deadly accurate with a 200 grain Cast Bullet out to distances I won't talk about.

Let's talk about recoil in the 35 Calibers.  Wheelman had talked about a 250 grain bullet.  

I made some searches using a meager 200 grain bullet in a 15" barrel on several 35 cartridges.  But first, I ran a 44 Magnum handgun with a 6" barrel and a 265 grain bullet moving out of the barrel at about 1261 fps.

The recoil on the 3 pound gun is a meager 18.89 foot pounds of recoil.  I say meager 'cause the 350 Remington Mag out of a 5.56 pound encore with scope runs 33.02 foot pounds of energy.  You might say, "well, that's only 14 or so more pounds than a 44 Mag.  It is my opinion that recoil is very subjective and the effect differs from person to person.  Another opinion is that the difference between an earthquake of number 5 on a Rector Scale is severe, but a 7, which is only two pointsmore is exponentially more severe, like doubled. I like to call the recoil scale "The Rectal Scale" simply because more recoil not only causes more pain, it also causes a certain tightening of a major organ just as you prepare to pull the trigger.  This Rectal effect causes me to want to close my eyes and pucker up when I think the gun is going off.  I'm kidding!!!  Sort of!!!!

I ran several loads for data and I started with the 350 Rem Mag.  I'll list the bullet, Powder, Velocity, Recoil, Energyat 200 yards and the % Powder burn in the 15" barrel.  The % powder burn in the barrel is very important for muzzle blast and noise.

Bullet,   Powder,  Velocity,  Recoil,    200 yd.Energy ,     % Powder burn

200 gr. Hornady SP bullet used in all calculations below
350 Rem Mag.
60 gr IMR4064, 2434 fps, 30.95 fpe,    1234 fp,                 92% Burn
59 gr IMR4895, 2531 fps, 33.02 fpe,    1330 fp                  95% Burn

35 Whelan Improved
59 gr IMR 4895, 2494 fps, 31.62 fpe,   1240 fp,                 94% Burn

358 Winchester
IMR4198,           2278 fps, 22.00 fpe,   1034 fp,                 99% Burn

35 Remington
37.7 gr IMR3031, 2039 fps, 18.46 fpe,  811 fp,                   88% Burn
28 gr IMR4227,    1928 fps, 14.54 fpe,  728 fp,                   97% Burn

For a comparison with a known caliber that has killed more animals on the  American continent that all other calibers put together.  I submit the following:
A 30-30 Winchester with a 170 grain bullet from a 20" barrel carbine will produce 1415 foot pounds energy at 50 yards and 886 foot pounds energy at 200 yards.

I shoot over 10,000 rounds a year in rifles and TC Encores and Contenders.  If I had to tolerate over 15 pounds of recoil energy, I would not be shooting at all.

Another suggestion:  Keep the Rubber Grip and forget the pretty wood where you are going.  I have fired full blown 308s with Wood form fitting grips.  I use only Rubber Grips.

This is just an opinion and study the notes above for what it's worth.

Harold Clark
seventcu @ citlink.net  Remove the spaces to use the address.

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #16 on: May 21, 2005, 06:00:32 PM »
Harold,
thanks for the input.  You know you made a HUGE mistake when you got rid of that .357 Max barrel-my favorite Contender cartridge-hands down.  I like the .223 very much also, but that's a different animal.  The 180gr Hornady SSP out of a 14" barrel in the Max is about as much as you can get for the little recoil price you pay, much easier on the hands than any 44 mag barrel I've shot...at least it feels that way to me.  I've got Pachmeyr grip and forend with a Luepold 4x on mine, so it weighs plenty, but it's very accurate with jacketed and cast.

I've got a pretty good idea of what I'm getting into, at least I think so.  The muzzle brakes are very loud, but very effective.  The difference in my XP-100 in .284 Winchester is day and night with the brake on or off the barrel.  It goes from a wrist wrencher to a pussycat, even with the 160gr loadings.

I am a little apprehensive about the recoil, but if it's too much I can always sell it.  SSK barrels with dies on Ebay bring tidy sums of cash when they show up there,not to mention outright selling on the various forums.  I know my .35 Whelen AI gives you plenty push when you spit 250gr bullets out at 2600+fps in a rifle that weighs over 8 lbs.

Offline haroldclark

  • Trade Count: (13)
  • Contributor
  • ***
  • Posts: 460
Hello Wheelman
« Reply #17 on: May 21, 2005, 06:20:34 PM »
Now if you are talking muzzle brakes, we are talking a different story on recoil.  I can't shoot much of anything without a brake.  My old wrists and elbows are reall complaining.

I have used the HP Howizter, the Darryl Holland and one by Van Horn.  The really work.  I'm going to put the Howizter on my 7mm BR Encore.  I took if off of my 308 and put on a Holland, but the Howizter is just a bit more effective.

I have a buddy that shoots a Virgin Valley 6.5 WSSM with an 18.5 barrel plus the Howizter.  There is virtually no recoil.

Usually, when I mention Muzzle Brakes on this forum, most guys go goofy over the noise.  It's not that bad if you wear hearing protection like we should.  I shoot with a group of guys (12 of us) and only one guy doesn't have a muzzle brake on his barrel.

I started a Long Range Handgun Shoot (Match) a year ago at our range.  We shoot once a month.  I set a max barrel length of 20" including any brakes.  We have had 4 - 40s fired.  40 is a perfect score.  We shoot out to 500 meters and we need power to get there and take the steel rams.  Without a muzzle brake, we most likely couldn't  finish a 40 round course. Actually, we shoot anywhere from 50 to 60 rounds on a 40 target course.  All over 40 shots are sighters for the different distances.

Lots of luck with your purchase.

The reason I traded my 357 Maxi was that I needed better velocity and trajectory out to 500 meters.  I have taken many rams with the Maxi barrel with 200 grain cast bullet.  I had Wiliams open sights on it and I had elevation out the yang.

Harold

Offline fyrepowrx

  • Trade Count: (6)
  • Avid Poster
  • **
  • Posts: 245
Best .35 cal for Encore pistol
« Reply #18 on: May 22, 2005, 04:44:55 AM »
There was an article fairly recently, (in Shooting Times maybe?...dont remember) about the efficiency of various cartridges. It compared the powder consumed against the Energy generated, and after comparing a bunch of loads, several dozen in many calibers, the end result was the the 35 Whelen AI took first place in efficiency.

It did not have the least recoil by any means, nor did it shoot the flattest, but it did yield more energy for grain of powder consumed than all the others tested. I though that was somewhat interesting, it beat out the favorites, such as the 7mm & 300 mags, the 7mm-08 & .308, etc... Not sure how that efficiency would transfer over to short barrels, but it sure seems that it would still rate fairly high even in shorter tubes..

Harold is right about recoil, i have a custom shop Remington model 7 in .350 mag that has the Kevlar stock, it weighs in the 6 pound range scoped, only a bit more than a 15" encore pistol,  and it beats the crap out of me... That extra 14 pounds of recoil makes a difference!
8) There is plenty of room for all of God''s Creatures...Right beside the mashed potatoes.. 8)

Offline haroldclark

  • Trade Count: (13)
  • Contributor
  • ***
  • Posts: 460
Fyrepower mentioned Efficiency
« Reply #19 on: May 22, 2005, 05:24:53 AM »
I don't have much to go on to determine efficiency of a cartridge,  but I do have Computer Software Quickload that calculates the efficiency for me.  I develop the load with all minute details that include seating depth, OAL, exact bullet info, powder, barrel length and so on.
 
I have studied hundreds of loads to determine what powder, bullet and barrel length combinations provide the best barrel burn rate and the efficiency.  It is interesting that the smaller the cartridge, such as a 7mm BR, will provide a great efficiency rating and not give the best burning rate.  I like 100% powder burn in the barrel if possible no matter how rare that may be for full house loads.  However, the perfect loads don't always shoot perfectly (accuracy).
 
For Comparison I have added the 7mm BR with Hornady 162 gr Amax bullet and 28.8 grains of BLC-2 powder at 2115 fps from a 18.5" barrel with 1.5" muzzle brake.
 
7MM BR:  96% Barrel Burn rate with 29.3% efficiency.
 
I have added the efficiency rating below.
 
Bullet, Powder, Velocity, Recoil, 200 yd.Energy , % Powder burn, Efficiency.
 
200 gr. Hornady SP bullet used in all calculations below:
350 Rem Mag.
60 gr IMR4064, 2434 fps, 30.95 fpe, 1234 fp, 92% Burn/24% Efficiency
59 gr IMR4895, 2531 fps, 33.02 fpe, 1330 fp 95% Burn/26% Efficiency
 
35 Whelan Improved
59 gr IMR 4895, 2494 fps, 31.62 fpe, 1240 fp, 94% Burn/25% Efficiency
 
358 Winchester
IMR4198, 2278 fps, 22.00 fpe, 1034 fp, 99% Burn/32% Efficiency
 
35 Remington
37.7 gr IMR3031, 2039 fps, 18.46 fpe, 811 fp, 88% Burn/26% Efficiency
28 gr IMR4227, 1928 fps, 14.54 fpe, 728 fp, 97% Burn /30% Efficiency
 
And the beat goes on and on and on.
 
As a final note, there are many choices in cartridges.  When we are young and still invincible, we shoot cannons, but not very much or often.  When we get older and shoot more, our cannons diminsh to pea shooters.  It is a cycle of life.  I'm in the pea shooter stages.  I'm still having a great time playing with my toys.
 
Harold Clark

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #20 on: May 25, 2005, 06:39:00 AM »
Harold,
I hear what you're saying about the recoil.  I'm not into my "advanced" years by any means.  I have been shooting magnum handguns 17 years and working with my hands for the better part of 15, not to mention the damn computer mouse.  I look for chamberings that do what I want, with the ability to do more if need be, and try to find the most comfortable firearm to fire them from.
 
Part of the decision for the 35-06 JDJ was that I came across a new barrel with the arrestor brake for a very good price.  I usually don't get the best accuracy with cartridges loaded all the way to maximum and I doubt this will be an exception, but it'll likely have a little gas in the tank if I feel I need it.  The fact that I have lots of different suitable .35 bullets, moulds, sizers, case prep tools, etc make the decision sound to me.
 
I guess I'll just have to pay my money and take my chances.

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26999
  • Gender: Male
Best .35 cal for Encore pistol
« Reply #21 on: May 25, 2005, 07:52:35 AM »
Unless you are just a glutton for punishment take a long hard look at the .358 JDJ. From my 14" Contender I was getting 2300 fps with 225s and still hadn't reached JD's max powder charge. It's a rimmed case which really is best in the TCs and has more capacity than the .358 Win. and almost as much as the .35 Whelen. JD has plenty of load data for it and it is to me the ideal .35 for the TCs if you're not real recoil sensitive. In an Encore recoil should be less than in the Contender. With the SSK Arrestor muzzle break there is zero barrel lift off the bags.

From an Encore you should be able to safely get at least 2400-2500 fps with 225s and within 100 fps of same with 250s I'd think.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #22 on: May 25, 2005, 02:46:15 PM »
GB,
thanks for the info on the barrel.  What revolver would you compare the recoil to, with the setup you had?  From your comment, I'm guessing you had the arrestor on that barrel.

The numbers you anticipate seem a little optimistic...that's right in .35 Whelen rifle territory.  You never know until you try though, that part of the fun of it for me.  I've been quite suprised by the numbers people are getting out of full on rifle cartridges in the Encore, especially the magnum rifle rounds.  My .284 loses about 250-300 fps as compared to a 22" rifle barrel when fired from my 15" XP-100.  My guess says the larger the bore, the less the loss, but it doesn't always work out that way from what some shooters are claiming.  I am going to stay with my original choice, I can't turn down the price on this barrel.  I'm pretty certain I could resell it for the same as I'm paying AFTER I've fired it enough to see if it's the round I want.

I realize that many TC shooters, I've shot quite a few different rounds in the Contender myself, like a rimmed case for headspacing purposes.  I've never had a headspace problem shooting rimless cases.  Do the problems some folks have with case head separation come from the frame flexing?  I would think that would cause the same problem rim or no rim.

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26999
  • Gender: Male
Best .35 cal for Encore pistol
« Reply #23 on: May 25, 2005, 05:39:42 PM »
Quote
GB,
thanks for the info on the barrel. What revolver would you compare the recoil to, with the setup you had? From your comment, I'm guessing you had the arrestor on that barrel.


I'm not sure I could compare it to any revolver I've ever fired. If I had to pick one it would be the FA83 with no scope and shooting the heavy bullet COR-BON loads. Vicious is the word I'm looking for. BUT the recoil is different.

With an unported barrel the gun rises over a foot off the bags and twists violently to the left. It hurt my wrist but be aware I have arthritis in my hands and wrists and that might be a factor. So I sent the barrel back to SSK for the Arrestor brake. When it came back it had zero lift off the bag and zero twist. NONE. NADA. But oh did it come straight back into the web of my hand. And for me that was even worse. I have a bone spur or calcium deposit or something in the web of my right hand and I just was not able to deal with the pain it caused me. I had to sell the barrel.

Quote
The numbers you anticipate seem a little optimistic...that's right in .35 Whelen rifle territory. You never know until you try though, that part of the fun of it for me. I've been quite suprised by the numbers people are getting out of full on rifle cartridges in the Encore, especially the magnum rifle rounds. My .284 loses about 250-300 fps as compared to a 22" rifle barrel when fired from my 15" XP-100. My guess says the larger the bore, the less the loss, but it doesn't always work out that way from what some shooters are claiming. I am going to stay with my original choice, I can't turn down the price on this barrel. I'm pretty certain I could resell it for the same as I'm paying AFTER I've fired it enough to see if it's the round I want.


Perhaps you'd think so but I used an Oehler 35M chrono to clock the 2300 fps from a 14" Contender in a rechambered TC factory barrel. Those usually get less velocity not more than an SSK barrel. And I was still 1.5 grains below the maximum charge of AA2520 that the SSK data showed was safe in a Contender.

We all know the Encore can take much higher pressures safely than can the Contender. I have no doubt I could have safely used 3 or maybe 4 more grains of powder IF it had been an Encore. And in a larger heavier gun like the Encore recoil would be lessened.

Now to me 2300 fps from a Nosler 225 PT or BT is more than enough for anything I'd take on with it. I can see no reason at all why you couldn't add 150-200 fps with the higher pressures allowed in an Encore IF you really wanted them. I didn't. It was already more than I could handle.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline WhelenMan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 24
Best .35 cal for Encore pistol
« Reply #24 on: May 25, 2005, 06:23:53 PM »
GB,
2300 with a 225 is enough to take on most anything, whether you'd want to or not! :)

It will be a mid summer before I get to playing with this seriously, but I'll let you know what it will do if I can take the recoil of it.

Offline Big Gun

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 120
Best .35 cal for Encore pistol
« Reply #25 on: June 23, 2005, 05:14:13 AM »
I got around to testing the fire forming loads for my 35-06 JDJ last night - worked pretty well.  Using Hornady 250 GR pointed sp bullets seated out to the lands of the rifling.  Started with 35 Whelen brass, loaded with 51 Gr of RL15.  It was a pretty good handfull off of the bench, I only shot 9 rounds (had 10 loaded up), and managed to get it shooting a couple inches high at 50 yds.  I will be loading up some more of these soon, I plan to use this gun for a Bison hunt this fall, not sure what bullets I will use yet.  I bought some of the 180 GR Hornady SSP bullets - might be too light for Bison though, also considering the 225 GR NBT, so far the 250 GR Hornadys do not look like a bad choice either.

Whelenman - have you got anything loaded up for yours yet?
Contenderize 'Em

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26999
  • Gender: Male
Best .35 cal for Encore pistol
« Reply #26 on: June 23, 2005, 10:05:31 AM »
For Bison I'd stick with a 250, either the Hornady or Nosler.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!