« previous next »
Pages: [1]   Go Down

Author Topic: Tuning a conibear  (Read 1884 times)

0 Members and 3 Guests are viewing this topic.

Offline Whistler

  • Trade Count: (0)
  • Member
  • *
  • Posts: 12
Tuning a conibear
« on: October 19, 2005, 03:23:35 AM »
I was checking out some conibears (110's) and noticed how much pressure was needed to set these off. Also the trigger travel was much further  than I expected before tripping the trap.

Anyone know of any articles on tuning a conibear or have suggestions?
Logged

Offline Bogmaster

  • Moderator
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2743
Tuning a conibear
« Reply #1 on: October 19, 2005, 05:32:07 AM »
At times,the trigger bracket may be pinched to tightly.This causes a hard firing trap,and also affects the trigger travel.
 Take a flat end screw driver and open this bracket a bit.This allows the bracket to swing more freely on the jaw.Less pressure is then needed to fire the trap,it will also decrease the trigger travel.
 Tom
Logged
If you need trapping supplies---call ,E-mail , or PM me . Home of Tom Olson's Mound Master Beaver Lures  ,Blackies Blend--lures and baits.Snare supplies,Dye ,dip,wax,Large assortment of gloves and Choppers-at very good prices.Hardware,snares,cable restraints and more!Give me a call(651) 436-2539
  I now also carry --- The WIEBE line of Knives and their new 8 and 12 inch fleshing Knives.

Offline fishdaddy

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 750
Tuning a conibear
« Reply #2 on: October 19, 2005, 04:09:47 PM »
a good tip i tried it and it worked on a 330 now less than half the travel before fireing now im more scared of it than before. :grin:

 fish.
Logged

Offline Bogmaster

  • Moderator
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2743
Tuning a conibear
« Reply #3 on: October 19, 2005, 04:32:26 PM »
Fish,a safety grippers is what to use,when handling 330s.I won't set one anymore ,without using one.
 Tom
Logged
If you need trapping supplies---call ,E-mail , or PM me . Home of Tom Olson's Mound Master Beaver Lures  ,Blackies Blend--lures and baits.Snare supplies,Dye ,dip,wax,Large assortment of gloves and Choppers-at very good prices.Hardware,snares,cable restraints and more!Give me a call(651) 436-2539
  I now also carry --- The WIEBE line of Knives and their new 8 and 12 inch fleshing Knives.

Offline Whistler

  • Trade Count: (0)
  • Member
  • *
  • Posts: 12
Tuning a conibear
« Reply #4 on: October 21, 2005, 11:48:42 AM »
I checked the crimps and there were a couple that were tight and adjustments helped those somewhat. (Thanks, Bogmaster) However they are still hard and a long travel in needed to fire them. I remember reading some info about tuning a conibear. I though a member might have also read the article or web page and remember where I saw it.
These traps are brand new and I plan to use them for rats. I have some concern that a rat couldn't fire them without a good run at them!!! Got to be a way to correct this.

I use a small C-clamp instead of a safety gripper just because that's what I have when I set 330's. A little awkward with cold hands haven't used the gripper so I couldn't compare[/quote]
Logged

Offline steven49er

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 134
Tuning a conibear
« Reply #5 on: October 23, 2005, 05:13:59 AM »
If you have too much travel in your trigger it is because your dog isnt seated deep enougn on the trap jaw.  I correct this with a round chainsaw file.  File the groove deeper so the dog will seat deeper on the trap jaw.  I like mine on my 330s to sit right on the trigger.  

Side note be careful if you do any filing if not done properly the trap will go off on its own.
Logged
Pages: [1]   Go Up
« previous next »