Author Topic: Home made snapcap  (Read 511 times)

0 Members and 1 Guest are viewing this topic.

Offline aulrich

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 678
Home made snapcap
« on: January 25, 2006, 04:51:16 AM »
I read this on another forum, in concept it seems OK, and since handi's should not be dry fired I though I'd post it here for discussion. In a nutshell the fella would glue a piece of eraser in a primer pocket and use that as a snap cap.  does that seem reasonable to you?
The second mouse gets the cheese

Offline dodd3

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1004
  • Gender: Male
Home made snapcap
« Reply #1 on: January 25, 2006, 05:41:23 AM »
aulrich i have heird of putting silicon in the primer pocket, so the eraser is just an other way to do it.

bernie :D
if its feral its in peril

Offline Busta

  • GBO Supporter
  • Trade Count: (5)
  • Senior Member
  • *****
  • Posts: 2586
  • Gender: Male
Home made snapcap
« Reply #2 on: January 25, 2006, 05:41:34 AM »
Done it myself for my Huntsman. Put it in the primer carrier and it works. You will have to trim down the diameter though. I'm not saying it is the best alternative but it is easy and cheap. I also have the .25 ACP plug for my Huntsman and have taken a auto vacuum line end cap and cut it to length. You might be able to find another piece of rubber the right diameter.

I haven't had a problem, YET! :wink:
U.S.A.F. Veteran
NRA Life Member

Offline aulrich

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 678
Home made snapcap
« Reply #3 on: January 25, 2006, 06:05:34 AM »
I was thinking aquaseal (wader repair glue) could work too a little tougher than silicon. I think the comercial ones would be better but I have not seen one for 204 yet.
The second mouse gets the cheese

Offline bladerunner

  • Trade Count: (2)
  • A Real Regular
  • ****
  • Posts: 506
Home made snapcap
« Reply #4 on: January 25, 2006, 04:10:35 PM »
aulrich,found this for ya
http://www.pistoleer.com/azoom/rifle/

hope that helps,they list the 204R   :D
Good shot placement + well constructed bullet = DEAD
 
                               Matt B.

Offline FirstFreedom

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 163
Home made snapcap
« Reply #5 on: January 26, 2006, 12:23:01 PM »
I dry fire my Handis all the time....should I not?

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Home made snapcap
« Reply #6 on: January 26, 2006, 12:42:40 PM »
It states in the Owner's Manual under Loading and Firing...

Quote
NOTICE: This firearm should never be dry fired, as damage could occur to the barrel and/or the firing pin.


The barrel damage would occur on rimfires, I also suspect the transfer bar could be broken by dry firing.

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline aulrich

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 678
Home made snapcap
« Reply #7 on: January 26, 2006, 02:21:03 PM »
The aquaseal is looking good so far, As long as it sticks to the pimer pocket. Bladerunner I have to keep purchases down right now, I have got a 10/22T on layaway so wvery penny counts right now. :-D But I have saved the link
The second mouse gets the cheese