www.GBOReloaded.com
Home
Help
Articles
Classifieds
Login
Register
Graybeard Outdoors (GBO Reloaded)
»
Black Powder Forums
»
Cap and Ball Revolvers & Pistols
(Moderator:
Flint
) »
Managing Colt Pocket Police
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Managing Colt Pocket Police (Read 1264 times)
0 Members and 3 Guests are viewing this topic.
Sir Charles deMoutonBlack
Trade Count:
(
0
)
Contributor
Posts: 323
Managing Colt Pocket Police
«
on:
May 16, 2006, 05:19:40 AM »
I've had a bit of trouble with my Uberti Colt 1862 Pocket Police.
15 to 17 grains of 3F seems about right, but I can't make cigarette paper cartridges work because there doesn't seem to be enough room to get them in. I thought .375 balls were too small so I got a LEE .380 mould. They are TOO LARGE!
Here's the real kicker. I have some RWS #55 caps, #10 size, but a little taller. On firing, a bit of cap goes straight down into the gap by the hammer. It imediately locks everything up. To free it I turn the pistol over and wiggle the hammer, and shake the gun until the fragment drops out. I don't even get the chance to do the upwards flip cocking manoeuvre to keep the caps out!
I will try Ruger OA nipples next, with #11 caps. Does anyone have any tips to keep these tiny things tickin'?
Logged
longcaribiner
Trade Count:
(
0
)
Contributor
Posts: 376
colt pocket police
«
Reply #1 on:
May 16, 2006, 07:17:54 PM »
Same gun same problem. With No 11 CCI caps. I tried some old CVA brass caps, they stuck to the nipples just fine,,,,,, a little too stuck, had to scrape em off with a knife. If anyone has the cure, please post. Otherwise it is a great little gun.
Logged
wilded
Trade Count:
(
0
)
Member
Posts: 75
http://wildedtx.blogspot.com/
Managing Colt Pocket Police
«
Reply #2 on:
May 17, 2006, 03:03:04 PM »
replace the nipples. :-)
Logged
Make time for the important things in life.
http://wildedtx.blogspot.com/
Ed Thomas
Sir Charles deMoutonBlack
Trade Count:
(
0
)
Contributor
Posts: 323
second test; CCI #10 caps
«
Reply #3 on:
May 18, 2006, 04:52:34 PM »
Ed; I've ordered some Ruger nips. I found some CCI #10 caps in my Gatherin's. (What me Troublin calls JUNK!)
They don't fall IN the action, but they do fall OFF! It seems they are a tad larger than the RWS #55's. I guess I'll have to tweak them prior to capping.
Logged
longcaribiner
Trade Count:
(
0
)
Contributor
Posts: 376
Colt police
«
Reply #4 on:
May 22, 2006, 08:24:58 AM »
Ruger Nipple will fit?
Logged
Sir Charles deMoutonBlack
Trade Count:
(
0
)
Contributor
Posts: 323
Thread sizes for nipples
«
Reply #5 on:
May 22, 2006, 05:50:29 PM »
Long Caribiner; I have done it on my Uberti '51 Navy. I works well. I checked the Thunderridge site. (BTW, a great site that I just discovered through a discussion on CASCITY forums, the DARKSIDERS DEN) They state that All Ubertis take #12 x 28 threaded nipples, as do Rugers. Piettas take 6 x .75mm.
Logged
ashtekk
Trade Count:
(
0
)
Posts: 1
Re: Managing Colt Pocket Police
«
Reply #6 on:
September 13, 2006, 02:18:27 PM »
I shoot the pocket navy and have the same problem on occaision. I have started to squeeze the caps a little and that seems to put a light crimp and it helps them stay on, but not too tight. The other thing I read about and will try is that they used to raise the gun into the air during cocking after each shot so that the spent caps would fall off. otherwise a cool little weapon.
Logged
howdy doody
Trade Count:
(
0
)
Contributor
Posts: 453
Re: Managing Colt Pocket Police
«
Reply #7 on:
September 13, 2006, 08:21:24 PM »
UH, OH. The Rugers have sae threads and you will find you need metric sized. Then there is always the height issue too. I am sure Treso makes nipples for your 1862 and they take #10 Remington caps. I have bought Treso nipples from Buffalo Arms. See what they have. The thing that makes the Treso work so well is the smaller flash hole. After firing, the caps aren't so easily blown back.
Logged
yer pard,
Howdy Doody
Darksider from Doodyville USA
Sir Charles deMoutonBlack
Trade Count:
(
0
)
Contributor
Posts: 323
Re: Managing Colt Pocket Police
«
Reply #8 on:
September 14, 2006, 05:18:36 AM »
Ruger cones work so well on my Uberti police that I probably won't even bother with Thunder Ridge. Someone else, somewhere else, also noted the SAE/Metric difference, but it doesn't seem enough to stop them from working well!
Logged
Flint
Moderator
Trade Count:
(
0
)
Senior Member
Posts: 1053
Re: Managing Colt Pocket Police
«
Reply #9 on:
September 14, 2006, 08:03:03 AM »
Uberti also used metric threads (M6x.75) before they made the Colt 2nd generation parts. They switched to #12-28 for the Colts. (even though the original Colts were .225-32).
Incidently, the #12-28 translates to M5.5x.90, so it could be considered metric as well, though not a standard DIN or ISO screw thread.
I have used Ruger nipples in several Ubertis, though I made and installed .01 to .015 thick shim washers under them to reach the hammer, as the Ruger has a slightly shorter cone. Lately, however, I favor the Treso nipple, available from Thunder Ridge.
Logged
Flint, SASS 976, NRA Life
howdy doody
Trade Count:
(
0
)
Contributor
Posts: 453
Re: Managing Colt Pocket Police
«
Reply #10 on:
September 14, 2006, 02:35:44 PM »
Please allow me stand corrected. Flint is my authority any day when it comes to C&Bs. Pardon me please. I was thinking of the Uberti model.
Logged
yer pard,
Howdy Doody
Darksider from Doodyville USA
Print
Pages: [
1
]
Go Up
« previous
next »
Graybeard Outdoors (GBO Reloaded)
»
Black Powder Forums
»
Cap and Ball Revolvers & Pistols
(Moderator:
Flint
) »
Managing Colt Pocket Police