Author Topic: sights for a 30AS?  (Read 766 times)

0 Members and 1 Guest are viewing this topic.

Offline demented

  • GBO Supporter
  • Trade Count: (20)
  • A Real Regular
  • *****
  • Posts: 577
sights for a 30AS?
« on: February 20, 2006, 10:07:43 AM »
All the sights from Williams, Hi-Viz, Marbles are listed to fit 336's with ramped front sights.  Mine are dovetailed so I am looking for some that will work.  Anyone with any info will be appreciated!  Thanks!

Offline Bubba w/a 45/70

  • Trade Count: (0)
  • Member
  • *
  • Posts: 81
sights for a 30AS?
« Reply #1 on: February 23, 2006, 02:13:30 AM »
The sights listed should just be screwed into place, totally replacing the factory Marlin front sights.  

You would have to first remove the screws from the front sight, remove the sight, and then inverse the order of removal for the new sights.


Anyone can correct me if I'm wrong.
"I SHOOT BACK!"     Uncle Ted

Offline Winter Hawk

  • Trade Count: (47)
  • Senior Member
  • *****
  • Posts: 1947
  • Gender: Male
sights for a 30AS?
« Reply #2 on: February 24, 2006, 06:07:56 PM »
You are talking about front sights, right?  I assume that when you say your sights are dovetailed, you mean that the dovetail is cut in the barrel.  The ramps are also dovetailed for the sights, just the ramp screws to the barrel so it raises the front sight.  The sight itself goes into the dovetail on the ramp.  You need to measure your existing sight from the bottom of the dovetail to the top of the sight, then find one of about the same height and it should slide right into place.  You might also want to look at Williams Shorty Ramp.  They have one which has a dovetailed piece which slides into the dovetail and the ramp is screwed into this adapter.

-WH-
"All you need for happiness is a good gun, a good horse and a good wife." - D. Boone

Offline smokey262

  • Trade Count: (17)
  • Avid Poster
  • **
  • Posts: 139
sights for a 30AS?
« Reply #3 on: February 26, 2006, 01:24:22 PM »
My Dad gave me his old 30AS a few years before he passed on, and I put a Williams Foolproof receiver sight on it last fall.  This rifle has a dovetail cut into the barrel, and to boot, the barrel band is very close to the dovetail.  I tried a few different front sights from Williams and Marbles with no luck.  They were not high enough to bring my point of impact  down to the point of aim even with the rear sight adjusted as low as it would go.

After tons of searching, the solution was a front sight from XS Sights.  It is a very nicely made white line post that is the perfect height.  It is not on their website, or in their catalog.  I called them and told them what I was looking for and the guy said it was for a Winchester lever action.  I explained the situation about the barrel band, etc. and he said no problem.  If I recall, it was about $35 or so

Got it in a few days, installed it and went to the range.  Works perfectly!

If you like I could fine the package and give you the part number, etc., or post a picture

Offline stennett

  • Trade Count: (0)
  • Posts: 4
sights for a 30AS?
« Reply #4 on: March 09, 2006, 05:34:12 PM »
Yes, any information on those sights would be appreciated, especially a pic and link to the company that sold it.

Offline DavidBrock

  • Trade Count: (0)
  • Posts: 1
Sights for 30AS
« Reply #5 on: April 27, 2006, 08:35:14 PM »
I just picked up a 30AS and it came with a 4x Tasco scope but I'm fond of peep sights.  I'd light to know more about the XS solution that worked for you.

Offline ScoutMan

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 287
sights for a 30AS?
« Reply #6 on: April 29, 2006, 01:57:46 AM »
Dave,

I have the XS combination on a Ruger Compact and love it.

Points to ponder:
1-Use the largest aperture available. For field use there's no appreciable difference in accuracy. (Mine is .190, which is OK.)

2-Make sure to get a front post that is wide enough. Mine is .100. It is a click out of focus with my eyesigth (no glasses, 70 yrs old next month.)I've looked through a .125 width sight and that was in sharp focus. You won't gain much accuracy with a thinner front post, and the wider post makes sight acquistion much faster.

My $.02


SM
If you can get closer, get closer
If you can get steadier, get steadier.

A telescope helps you see; it does not help you hold and squeeze.-Jeff Cooper

Offline smokey262

  • Trade Count: (17)
  • Avid Poster
  • **
  • Posts: 139
pictures of front sight
« Reply #7 on: May 01, 2006, 03:09:49 PM »
I just saw that a picture of the front sight was requested some time back.  will post later tonight ot tomorrow

smokey 262

Offline sonnyottawa

  • Trade Count: (0)
  • Posts: 1
sights for a 30AS?
« Reply #8 on: June 24, 2006, 06:56:44 PM »
Quote from: smokey262
My Dad gave me his old 30AS a few years before he passed on, and I put a Williams Foolproof receiver sight on it last fall.  This rifle has a dovetail cut into the barrel, and to boot, the barrel band is very close to the dovetail.  I tried a few different front sights from Williams and Marbles with no luck.  They were not high enough to bring my point of impact  down to the point of aim even with the rear sight adjusted as low as it would go.

After tons of searching, the solution was a front sight from XS Sights.  It is a very nicely made white line post that is the perfect height.  It is not on their website, or in their catalog.  I called them and told them what I was looking for and the guy said it was for a Winchester lever action.  I explained the situation about the barrel band, etc. and he said no problem.  If I recall, it was about $35 or so

Got it in a few days, installed it and went to the range.  Works perfectly!

If you like I could fine the package and give you the part number, etc., or post a picture

....................................
Hi friend,

This is Sonny from Ottawa, i read your message about the XS sight that you use for your 30AS Marlin...yes, this is great, i am looking for a kit for my Marlin 30AS too..would you be so kind to give me the info about this kit., where to buy it.. Also i am thinking of using the Tang Rear Sight number 2... do you think this will work

Thank you so much for your help

Sonny