« previous next »
Pages: [1]   Go Down

Author Topic: Drill and Tap a NEf/H&R .410 shotgun?  (Read 1939 times)

0 Members and 1 Guest are viewing this topic.

Offline SSS

  • Trade Count: (0)
  • Member
  • *
  • Posts: 20
Drill and Tap a NEf/H&R .410 shotgun?
« on: August 13, 2006, 04:00:11 AM »
Can it be done safely?  Wouldn't mind putting a little red dot sight on a Tamer and getting a .22lr insert for it. ;D  Maybe for slugs too. 8)
Logged

Offline MSP Ret

  • GBO Supporter
  • Trade Count: (173)
  • Senior Member
  • *****
  • Posts: 8940
  • Gender: Male
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #1 on: August 13, 2006, 07:14:30 AM »
simple and safe for any competent gunsmith or even a hobbyist with a drillpress and a little skill. The chamber area on the .410 shotguns has plenty of thickness to safely D&T. Perhaps for more indepth info you might try the gunsmithing section, good luck....<><.... :)
Logged
"Giving up your gun to someone else on demand is called surrender. It means that you have given up your ability to protect yourself to a power that is greater than you." - David Yeagley

Offline je265

  • GBO Supporter
  • Trade Count: (56)
  • Contributor
  • *****
  • Posts: 263
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #2 on: August 15, 2006, 12:57:52 AM »
No problems drilling and tapping a 410. In fact the factory will even do it even do it for under $50 including the scope base and hammer extension.
Logged

Offline MSP Ret

  • GBO Supporter
  • Trade Count: (173)
  • Senior Member
  • *****
  • Posts: 8940
  • Gender: Male
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #3 on: August 15, 2006, 01:37:13 AM »
That's not a bad deal at all!!!! I say go for it....<><.... :)
Logged
"Giving up your gun to someone else on demand is called surrender. It means that you have given up your ability to protect yourself to a power that is greater than you." - David Yeagley

Offline SSS

  • Trade Count: (0)
  • Member
  • *
  • Posts: 20
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #4 on: August 15, 2006, 03:14:47 PM »
Thanks for the great info guys. :)
Logged

Offline SSS

  • Trade Count: (0)
  • Member
  • *
  • Posts: 20
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #5 on: August 15, 2006, 03:35:09 PM »
Quote from: je265 on August 15, 2006, 12:57:52 AM
No problems drilling and tapping a 410. In fact the factory will even do it even do it for under $50 including the scope base and hammer extension.

Do you know if that's the only with .410s?
Logged

Offline je265

  • GBO Supporter
  • Trade Count: (56)
  • Contributor
  • *****
  • Posts: 263
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #6 on: August 16, 2006, 11:21:45 AM »
That's correct, the factory will only drill and tap 410 smooth bore bbls. They sell the 20 and 12 ga Ultra slug bbls with scope bases but that's a different story.
Logged

Offline kenbev

  • Trade Count: (30)
  • Contributor
  • ***
  • Posts: 485
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #7 on: August 21, 2006, 01:48:15 PM »
Will they drill and tap a 45LC/410 barrel?
Logged

Offline myarmor

  • Trade Count: (46)
  • Senior Member
  • *****
  • Posts: 3239
  • Gender: Male
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #8 on: August 21, 2006, 07:00:48 PM »
I just thought I would throw this in. I plan on getting one, if not both of my 12ga barrels done. One is a 27" Mod Choke and the other a 24' Full Choke barrel. And this is the smith that I will get to do it. He's very fair and does a great job:
http://www.lowcountry-gunsmith.com/
In case anyone is looking.
-Aaron
Logged

Offline cwlongshot

  • GBO Supporter
  • Trade Count: (158)
  • Senior Member
  • *****
  • Posts: 9907
  • Gender: Male
  • Shooting, Hunting, the Outdoors & ATVs
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #9 on: September 02, 2006, 05:10:55 PM »
While its NOT a 410, it is a shotgun and its been fitted with peep sites and a front blade.





 I used a Contender fornt site and a Williams rear. I measured to get proper regulation for the front height. I also chopped the barrel to 19". its shoots quite well really. With 2 3/4" Rem Sluggers, it will keep three on a base ball at 50 yrds.

 I used it sucessfully on a couple porkers some years back....

CW
Logged
"Pay heed to the man who carries a single shot rifle, he likely knows how to use it."

NRA LIFE Member 
Remember... Four boxes keep us free: the soap box, the ballot box, the jury box, and the cartridge box.

Offline DaveH

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 438
Re: Drill and Tap a NEf/H&R .410 shotgun?
« Reply #10 on: September 03, 2006, 11:54:16 AM »
I know I'm just a dumb ole country boy... but why on earth would you want to put a red dot or a scope on a .410 ????

Logged
Dave H.
US Army SFC(Ret)
Pages: [1]   Go Up
« previous next »