« previous next »
Pages: [1]   Go Down

Author Topic: Remmy triggers..  (Read 563 times)

0 Members and 2 Guests are viewing this topic.

Offline RLB

  • Trade Count: (0)
  • Member
  • *
  • Posts: 51
Remmy triggers..
« on: September 09, 2006, 02:33:48 AM »
Is it possible to adjust the trigger on a 700 CDL.??? mine is right at 5 1/2lbs  I'd perfer 3 lbs...

RLB....
Logged

Offline billy

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 407
Re: Remmy triggers..
« Reply #1 on: September 09, 2006, 03:38:31 AM »
I ,m almost sure all rem. 700 triggers are ajustable,my adl is and set at 3 1/4 lbs.,gunsmith said that was low enough or might go off with a jar.
Logged
I enjoy collecting guns, swaping and staying up on all the newest models. I deer, quail, squirrel and rabbit hunt.

Offline RLB

  • Trade Count: (0)
  • Member
  • *
  • Posts: 51
Re: Remmy triggers..
« Reply #2 on: September 09, 2006, 03:44:49 AM »
hows it done.???

RLB.........
Logged

Offline ScoutMan

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 287
Re: Remmy triggers..
« Reply #3 on: September 09, 2006, 09:51:39 AM »
Go to Sniper Country and do a search. it's all laid out there. Real simple.

Caveat: There have been instances where the gun fired when the safety was moved to the fire position. In the trigger set up there is a disconnector type piece (can't remember the right name) which prevents this. However in order for this to operate properly the internal mechanism must not be dirty. Clean thoroughly with brake pad cleaner and lube sparingly the moving parts. Above all, donot spray the trigger unit with WD 40 to clean.
Logged
If you can get closer, get closer
If you can get steadier, get steadier.

A telescope helps you see; it does not help you hold and squeeze.-Jeff Cooper

Offline Val

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 846
Re: Remmy triggers..
« Reply #4 on: September 09, 2006, 04:05:59 PM »
I recently had the trigger on my Remy 700 Mountain rifle lightenedn by my gunsmith. Made a big difference and resulted in tighter groups.
Logged
Hunting and fishing are not matters of life or death. They are much more important than that.

Offline Hairtrigger

  • Trade Count: (10)
  • Senior Member
  • *****
  • Posts: 2010
Re: Remmy triggers..
« Reply #5 on: September 09, 2006, 04:12:54 PM »
Logged

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: Remmy triggers..
« Reply #6 on: September 09, 2006, 10:40:24 PM »
The parts you discussed in the 'trigger connector' (number 47 on the diagram at the link below). The problem stems from the safety moving the sear out of engagement with the striker when it is applied. If the part in question hangs as if it were in a sticky environment, it fails to reconnect or reset if the trigger is pulled with the safety applied. With the sear not reset if the saafety lever is moved to the off position it will fire. Clean the trigger as suggested with carb cleaner or brake cleaner(brake cleaner is likely better) and lube only with dry film lubricants.. If forced to use any for of oil, use it very, very sparingly!!! And always remember the first rule of firearms safety, 'never point the muzzle at anything you're not willing to destroy'!!!  With these triggers and most others I strongly advise against altering the factory sear engagement amount. If there is a significant amount of creep then it should be taken to a competant smith. Lightening the pull weight won't affect the sear engagement. Note the location of the adjusting screws on the attached diagram..
http://stevespages.com/ipb-remington-700.html
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."
Pages: [1]   Go Up
« previous next »