Author Topic: M-48A Rechamber  (Read 672 times)

0 Members and 1 Guest are viewing this topic.

Offline Turk

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 187
M-48A Rechamber
« on: March 01, 2007, 02:54:25 AM »
I have a couple of M-48A's and want to sportize one of them.  If I remember right the action is a little shorter than the 98 so can it be rechambered in 8mm-06 since the 06 case is 2.484 long and the 8mm rounds case is 2.240?

Thanks,

Turk
In God I trust all others bring data.
If you know you're going to a gunfight take a rifle.
Life Member 1/50th Infantry Association (Vietnam)
Member of the 173rd Airborne Association
Life member NRA & ORPA

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: M-48A Rechamber
« Reply #1 on: March 02, 2007, 06:50:55 AM »
I'm brain blinking just now but the simple answer is that the mauser can be safely made to take anything(almost) that'll fit in the magazine.. Measure the magazine, if the rounds fit your OK.. otherwise there will be length issues.. While the mag can be lengthened some there is a limit. Remember the feed ramp must catch the round as it exits the mag and it's the back of the lower locking lug abutment. Don't want to remove much,, if any!
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline iiranger

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 491
Well,...
« Reply #2 on: March 02, 2007, 07:06:05 AM »
O.K. the Mauser 8mm is 57 mm long. The '06 is, metric, 7.62 x 63 as I recall. POINT: If you insist on loading 220 grain bullets out to touch the rifling in a standard chamber... Magazine is too short. If you  are willing to load more common loads and be happy even if you have to deep seat a bullet now and again, no problem. Some 98's were coverted after WW II for allies and in the Belgium production there was a shallow groove cut in the rear of the front receiver ring so that you could extract unfired military 172 grain boat tail loads without hanging up on the front receiver ring... This is really splitting hairs. No reason you should not go for it. Great rifle if you want and budget permits custom. Mark X at wholesale was always cheaper after all the work was done, but that was "off the rack" factory... Your bucks. Luck. Happy trails.

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Re: M-48A Rechamber
« Reply #3 on: March 02, 2007, 03:53:34 PM »
I just wonder what a person could do with an 8MM-06 that couldn't be done with an 8X57? Other than spend way more on dies, loaded ammo, etc. 
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline Turk

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 187
Re: M-48A Rechamber
« Reply #4 on: March 03, 2007, 03:58:01 AM »
Guys, thanks for answering the question.

Nobabe

Quote
I just wonder what a person could do with an 8MM-06 that couldn't be done with an 8X57? Other than spend way more on dies, loaded ammo, etc.
 

Nothing its just having another caliber to shoot.

Turk
In God I trust all others bring data.
If you know you're going to a gunfight take a rifle.
Life Member 1/50th Infantry Association (Vietnam)
Member of the 173rd Airborne Association
Life member NRA & ORPA

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: M-48A Rechamber
« Reply #5 on: March 03, 2007, 09:49:12 AM »
Please don't get the rumor started that we need a REASON to owner another rifle!!! My wife might hear!!  In reality though they are close, but of course a trip thru the Ackley-izer and you mau get something like the 333OKH??
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."