« previous next »
Pages: [1]   Go Down

Author Topic: Dumb question about 45-70 reloading  (Read 447 times)

0 Members and 2 Guests are viewing this topic.

Offline Chancy Shot

  • Trade Count: (0)
  • Member
  • *
  • Posts: 9
Dumb question about 45-70 reloading
« on: December 09, 2008, 02:44:36 AM »
I just ordered a Buffalo Classic in 45-70 and want to start working up a load for it.  I have Winchester 45-70 brass and have ordered some 405 grain lead bullets, but cannot find any definite information on the primer to use.  I would assume it is a large rifle primer, but I hate to make assumptions about reloading.

Any other suggestions about a black powder load to start with would be appreciated. 

Thanks !!
Chancy
Logged

Offline aldar

  • Trade Count: (16)
  • Avid Poster
  • **
  • Posts: 246
Re: Dumb question about 45-70 reloading
« Reply #1 on: December 09, 2008, 03:21:25 AM »
yes they use large rifle primers. I just use Winchester for all my reloading as they are readily availbale near home. As for black powder loads, I cant help you there, but if i remeber right, there might be some info in the FAQ section under 45-70 loads. I have a Lyman manual and a LoadBook for mine. Both have sections on black powder loads.
Logged

Offline BBF

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 10042
  • Gender: Male
  • I feel much better now knowing it will get worse.
Re: Dumb question about 45-70 reloading
« Reply #2 on: December 09, 2008, 07:33:34 AM »
A very limited info from Lyman Black Powder Handbook:  Typical 45-70 load using a 405 gr Cast bullet with 70 grains( volume) Pyrodex RS gave 1250 fps from a 26" barrel.

caveat: If you are new to hand loading  let someone explain the difference between weight by scale and weight by volume to you. IT IS IMPORTANT !!!
Logged
What is the point of Life if you can't have fun.

Offline jhalcott

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1869
Re: Dumb question about 45-70 reloading
« Reply #3 on: December 09, 2008, 08:45:17 AM »
 As I under stand it, you should have NO air space between the powder and base of the bullet. A wad or some type of filler is required if black powder does not fill all the space in the case!
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Dumb question about 45-70 reloading
« Reply #4 on: December 09, 2008, 08:53:04 AM »
This is from the H&R FAQs and Help sticky, should help ya with the BP loads, the BC is just a fancy Handi with 10" more barrel!!  ;)

Tim

http://www.castbullet.com/shooting/1871.htm

http://www.gboreloaded.com/forums/index.php/board,126.0.html
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Sharps-Nut

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 334
Re: Dumb question about 45-70 reloading
« Reply #5 on: December 09, 2008, 11:41:11 AM »
You need to use a wad cut from tablet back or buy some veggie fiber wads.  The black powder should be compressed slightly, maybe 1/16" via powder compression die.  Then place the bullet over all this seated against the wad. Neck tensionor not is a much argued  point, you decide. Don't use your bullet to compress the powder as it will deform your soft lead bullet and cause accuracy issues. Do use a bpcr lube like shaver, dgl, spg. Loading black powder cartridge for accuracy can be a learning experience and great fun. Played the bpcr silhouette game for several years before selling out.  Crazy accuracy out to 500 meters if you do everything right.    Have fun.  SN
Logged
Pages: [1]   Go Up
« previous next »