« previous next »
Pages: [1]   Go Down

Author Topic: 1911 FIXED REAR SIGHT ADJUSTMENT  (Read 1968 times)

0 Members and 1 Guest are viewing this topic.

Offline Oldshooter

  • GBO subscriber and supporter
  • Moderators
  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 6426
1911 FIXED REAR SIGHT ADJUSTMENT
« on: January 27, 2009, 06:39:37 AM »
I've seen sigs rear sight adjustment tool and thought there was one for other pistols like 1911's
any ideas? and maybe someplace to get one!
Logged
“Owning a handgun doesn’t make you armed any more than owning a guitar makes you a musician.”

"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."

Offline Savage

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4397
Re: 1911 FIXED REAR SIGHT ADJUSTMENT
« Reply #1 on: January 27, 2009, 08:40:06 AM »
A rear sight tool can be had for about $100 from Brownell's. If you plan to change a lot of sights, it's worth the money. If you just need to change the sights on a pistol every now and then, or just want to adjust windage, use a drift punch and hammer.
Savage
Logged
An appeaser is one who feeds the crocodile hoping it will eat him last,

Offline Oldshooter

  • GBO subscriber and supporter
  • Moderators
  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 6426
Re: 1911 FIXED REAR SIGHT ADJUSTMENT
« Reply #2 on: January 28, 2009, 06:12:48 AM »
Been there done that! Also saw the 100 dollar tools. Friend has a new 1911 in stainless and needs a adjustment, hes scared to mar the finish. Was hoping there might be an economical way to do it without a hammer and punch. Thanks anyway, I appreciate the response.
Logged
“Owning a handgun doesn’t make you armed any more than owning a guitar makes you a musician.”

"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."

Offline Savage

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4397
Re: 1911 FIXED REAR SIGHT ADJUSTMENT
« Reply #3 on: January 28, 2009, 10:33:05 AM »
I hope your friend has benched his Kimber to make sure a windage adjustment is actually required. Too often it's the shooter rather than the gun. Guess he'll need to take it to a gunsmith to move the sight if needed.
Savage
Logged
An appeaser is one who feeds the crocodile hoping it will eat him last,

Offline Oldshooter

  • GBO subscriber and supporter
  • Moderators
  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 6426
Re: 1911 FIXED REAR SIGHT ADJUSTMENT
« Reply #4 on: January 28, 2009, 11:10:56 AM »
Actually its a Springfield Armory Mil Spec, He did bench shoot it once he saw it shooting left 2 inches at 10 yards. It wont take much and thats the reason I hate to tap on it, well one of the reasons.  ;)
Logged
“Owning a handgun doesn’t make you armed any more than owning a guitar makes you a musician.”

"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."

Offline skarke

  • GBO Supporter
  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1190
Re: 1911 FIXED REAR SIGHT ADJUSTMENT
« Reply #5 on: January 31, 2009, 03:52:00 PM »
Nylon or Delryn punch, then brass.  The brass wont mar the surface of steel, if used carefully.  Also, a good, padded vise is necessary.  Last, you could use a nylon bench block cut to fit the slide AND a good C clamp, but then, with all the carving and fitting, $100 sounds pretty cheap for a good tool.
Logged
Freedom is never more than one generation away from extinction. We didn’t pass it on to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same, or one day we will spend our sunset years telling our children what it was once like in the United States when men were free.  Ronaldus Maximus
Pages: [1]   Go Up
« previous next »