Author Topic: Removal of breech plug  (Read 852 times)

0 Members and 1 Guest are viewing this topic.

Offline Roundup

  • Trade Count: (0)
  • Member
  • *
  • Posts: 42
Removal of breech plug
« on: May 13, 2009, 07:51:37 AM »
Seeing I'm an old coot I'll ramble a bit here, but eventually I'll pose a question.  

Around 30 years ago I bought a new muzzle loader for all of $65.00!  Its a dead-ringer for many of the Hawken replicas I see retail for over $330.  Mine has brass furniture, is .50 caliber, shoots round balls a lot better than Maxi-balls, and has a birch rather than a walnut stock.

I have not shot it for quite awhile.  It has been fired approximately 200 times.  The only game I've use it on is sage rats and one coyote.  I have cleaned it thoroughly the same day I've shot it...  The old fashioned way with soap and hot water, and kept it well-oiled.  I've used both Black powder and Pyrodex.

My 14 year old Grandson is very interested in shooting it, so I'm resurrecting it and getting some new supplies.  My question is:  It has a hooked breech.  Is there any reason why I should unscreww the breech plug?  I've kept the gun very clean and there has been no evidence of rust or corrosion.

I'm open to advise.

Roundup
Happy Trails!

Roundup
NRA Life Member 1988
Semper Fi!

Offline SHOOTALL

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 23836
Re: Removal of breech plug
« Reply #1 on: May 13, 2009, 08:47:47 AM »
don't think I would
If ya can see it ya can hit it !

Offline Semisane

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 569
Re: Removal of breech plug
« Reply #2 on: May 13, 2009, 08:51:51 AM »
From one old coot to another - I think trying to unscrew the breech plug would likely be a big mistake.  Given your maintenance routine, I can think of no reason why I would do so.
CLICK ON ME: .
Link to... highchairstands@cox.net

Offline flintlock

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1405
  • Gender: Male
Re: Removal of breech plug
« Reply #3 on: May 13, 2009, 09:01:01 AM »
No...Leave it alone...

I started with these things in the 70s, have one I bought used in 1977, another I made in '88 and have never removed the breech plug on either...

Offline Roundup

  • Trade Count: (0)
  • Member
  • *
  • Posts: 42
Re: Removal of breech plug
« Reply #4 on: May 13, 2009, 01:29:31 PM »
Flintlock, Shootall, Semisane (I like that!)

Thanks for the reply.  To tell you the truth it was the answer I was hoping to get.  I thought I might be missing something important.  I didn't like the idea of buying a $7.00 tube of anti-seize either!

Roundup
Happy Trails!

Roundup
NRA Life Member 1988
Semper Fi!

Offline coyotejoe

  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 2937
  • Gender: Male
Re: Removal of breech plug
« Reply #5 on: May 14, 2009, 04:50:31 AM »
Many, probably most, old original ML guns have never had their breechplugs removed and it would be a bear to do so now. But then again, I've seen a few where the breechplug was just finger tight. My first muzzleloading gun, back in '58, was an old Ohio half-stock .36 caliber in which both the breechplug and nipple drum had their threads wrapped with sewing thread to take up the slack. I fired many shots from that old gun with no problem but I never loaded over about 30 grains of 2f in it. Ah yes, back when I was young and innocent, well, anyhow, I was young. ;D
The story of David & Goliath only demonstrates the superiority of ballistic projectiles over hand weapons, poor old Goliath never had a chance.

Offline Buckskins & Black Powder

  • Trade Count: (16)
  • Senior Member
  • *****
  • Posts: 1700
  • Gender: Male
    • Buckskins & Black Powder
Re: Removal of breech plug
« Reply #6 on: May 14, 2009, 01:24:58 PM »
If it aint broke, dont fix it.