« previous next »
Pages: [1]   Go Down

Author Topic: Looking for Taller Front Sight Blade for Contender Carbine  (Read 1151 times)

0 Members and 1 Guest are viewing this topic.

Offline Camp Cook

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 683
Looking for Taller Front Sight Blade for Contender Carbine
« on: April 28, 2009, 02:35:03 PM »
Does anyone know where I can buy a taller front sight blade for my T/C Contender carbine with factory stock iron sights?
Logged
<")))><

"A gun is a tool, Marian. No better, no worse than any other tool. An axe, a shovel, or anything. A gun is as good or as bad as the man using it. Remember that" -movie "Shane" 1953

Offline stubshaft

  • Trade Count: (8)
  • Contributor
  • ***
  • Posts: 489
  • ROA's Rule
Re: Looking for Taller Front Sight Blade for Contender Carbine
« Reply #1 on: April 28, 2009, 05:40:13 PM »
Back in the "day" when I shot silly wet.  I had a couple of barrels that shot too high.  I would take the front sight off of the barrel.  Remove the pin holding the blade in place.  Raise the blade and silver solder it in place.  You could even get by with JB Welding it in place from the bottom.

Just a thought.  Saved time and money...
Logged
If I agreed with you then we would both be wrong.

Offline Hopalong7

  • Trade Count: (20)
  • Senior Member
  • *****
  • Posts: 1673
  • Gender: Male
Re: Looking for Taller Front Sight Blade for Contender Carbine
« Reply #2 on: April 29, 2009, 12:39:14 AM »
Check with TC...I know at one time they had several different heights available.  Currently there are three different height front fire sights for the Encore rifle barrels, but I'm not sure about the Contender.  TC recently sent me a higher front sight for my Encore 12ga Turkey barrel very quickly and at no charge.
GOOD SHOOTIN', Walt  ;)
Logged

Offline Camp Cook

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 683
Re: Looking for Taller Front Sight Blade for Contender Carbine
« Reply #3 on: April 30, 2009, 04:03:17 PM »
Thanks I ordered one from T/C yesterday...  :D
Logged
<")))><

"A gun is a tool, Marian. No better, no worse than any other tool. An axe, a shovel, or anything. A gun is as good or as bad as the man using it. Remember that" -movie "Shane" 1953

Offline sbhg

  • Trade Count: (0)
  • Member
  • *
  • Posts: 81
Re: Looking for Taller Front Sight Blade for Contender Carbine
« Reply #4 on: May 06, 2009, 07:16:05 AM »
Quote from: Camp Cook on April 28, 2009, 02:35:03 PM
Does anyone know where I can buy a taller front sight blade for my T/C Contender carbine with factory stock iron sights?
Have a gunsmith cut a dovetail slot in it and install a fiberoptic sight (those things are wonderful) or
on a 6.5" barrel I have, I opened up the slot where the blade is and soldered in a colt .45 auto blade w/ a white dot. I used a blade w/ a long tennon, cleaned all blueing from the tennon only, used 50/50 lead solder. Works great and is just as accurate as w/ the thin factory blade.
Logged
"Experience is what you get when you don't get what you want."
Italian Proverb as retold by Jeff Cooper

Offline Camp Cook

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 683
Re: Looking for Taller Front Sight Blade for Contender Carbine
« Reply #5 on: May 18, 2009, 04:14:36 AM »
The front sight arrived I installed it right away and got out black bear hunting so I popped the scope off and give the iron sights a try when I found a nice safe spot now @ 100 yards I'm hitting a bit low need to raise the rear sight a bit more...  ;D
Logged
<")))><

"A gun is a tool, Marian. No better, no worse than any other tool. An axe, a shovel, or anything. A gun is as good or as bad as the man using it. Remember that" -movie "Shane" 1953
Pages: [1]   Go Up
« previous next »