Author Topic: barrel change??  (Read 689 times)

0 Members and 1 Guest are viewing this topic.

Offline original

  • GBO Supporter
  • Trade Count: (1)
  • Avid Poster
  • *****
  • Posts: 190
barrel change??
« on: December 23, 2009, 05:09:25 AM »
this may be a stupid question...i have a swede mauser and have seen barrels for sale from online places, is it possible to change the barrels on bolt actions rifles easily?  from different seasons if i wanted to keep pretty much the same gun but just change barrels out is it a lot more involved than just screwing one out and replacing with the newer one?

Offline bubba.50

  • GBO Supporter
  • Trade Count: (151)
  • Senior Member
  • *****
  • Posts: 1170
  • Gender: Male
Re: barrel change??
« Reply #1 on: December 23, 2009, 07:06:46 AM »
you can unscrew the existing barrel  and have a gun smith convert it and receiver to interupted threads. then you can have the barrels threaded with interupted threads to make it a switch barrel gun. each barrel would hafta be fitted and chambered and headspaced. also if scoped every time you switched barrels you'd hafta realign your scope. cost would also probably be kinda prohibitive. my opinion and worth what you paid for it. good luck and merry christmas friend, bubba.
fetch the hammer maggie-they's a bee on the baby's head!

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: barrel change??
« Reply #2 on: December 23, 2009, 05:04:58 PM »
It's very possible but it's not a good idea. The interupted threads usually don't prove satisfactory with high pressure rounds. They begin to loosen over time from the stress. Savage in the 99 had to switch to full threads when the interupted thread take downs started developing headspace problems.. The biggest problem is cost. The cheapest way to get a switchbarrel gun is to buy an Encore from TC. While a single shot that's not a huge problem for a hunting rifle and barrels are very reasonable. Rquire almost no tools and the telescopes are mounted to the barrel so for most practical purposes the sight in should be OK. I'd likely check it cnyway but that's just me..
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline roper

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 714
Re: barrel change??
« Reply #3 on: December 24, 2009, 05:06:38 AM »
this may be a stupid question...i have a swede mauser and have seen barrels for sale from online places, is it possible to change the barrels on bolt actions rifles easily?  from different seasons if i wanted to keep pretty much the same gun but just change barrels out is it a lot more involved than just screwing one out and replacing with the newer one?

Brownell sells Fitted mauser barrels large ring 98 and small ring 93-96 that are short chamber various calibers.  Most gunsmith can finish chamber by hand and set headspace.  The barrels list for the 93-96 are chamber for low pressure calibers 250 Sav,6.5x55 and 7x57 some of those barrels you see may not work if you have 93-96 mauser action.  Wilson,Pac-Nor also sell fitted barrel with short chamber for the mauser actions also.  I'm not sure if these are the type barrels you posted about but hope this helps.

Offline Kmrere42

  • Trade Count: (2)
  • Contributor
  • ***
  • Posts: 305
Re: barrel change??
« Reply #4 on: December 31, 2009, 10:45:05 AM »
Hi,

Just wanted to add a couple more pennies to the pile.


Get a Savage rifle with a box magazine. Not only can you change barrels quickly with a barrel nut setup but you can change bolt heads to fire almost any cartridge within reason. Savage bolts are 2-piece units that are easy to break down. Also most barrel makers that have pre-threaded barrels make fully chambered drop in barrels for the 10/110 series rifles.



Paul

Offline original

  • GBO Supporter
  • Trade Count: (1)
  • Avid Poster
  • *****
  • Posts: 190
Re: barrel change??
« Reply #5 on: January 11, 2010, 01:16:00 PM »
thanks for all the info.