« previous next »
Pages: [1]   Go Down

Author Topic: Laser Cast Bullets?  (Read 1049 times)

0 Members and 1 Guest are viewing this topic.

Offline coyotejoe

  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 2937
  • Gender: Male
Laser Cast Bullets?
« on: April 12, 2010, 06:52:52 AM »
I'm wondering what is the general opinion on these bullets? I've used a few in the past and contrary to their "guarantee" they did lead the bore in several revolvers of different calibers.  However, I just tried a few I had left over and they shot fine in my new 50th Anniversary Flat Top. They were 240 grain .431" SWC's and I loaded them in .44 special brass with either top end .44 special data or .44 mag starting loads. I was looking for about 1200 fps and most loads were around that number except for 6 grains of Bullseye, which went 974 fps and was the worst leading, and 6 grains of Trail Boss which gave me a 0.8" 25 yard group with only a trace of leading at 830 fps. The Elmer Keith load of 18.5 grains of #2400 went 1280 fps with no leading and a 2 1/2" group. 12 grains of HS-6 went into 2" at 1244 fps with no leading. That's all of those bullets I had on hand but I've just ordered 500 more. Their price seems quite reasonable at $67.50 with shipping included. I was wondering what opinions of other shooter may be on Oregon Trails Laser Cast.
Logged
The story of David & Goliath only demonstrates the superiority of ballistic projectiles over hand weapons, poor old Goliath never had a chance.

Offline timber1952

  • Trade Count: (0)
  • Member
  • *
  • Posts: 20
Re: Laser Cast Bullets?
« Reply #1 on: April 12, 2010, 05:39:09 PM »
I have used the 45 colt, 200 grain, 357 125 grain, 44 mag 200 grain all at low speed plinking load. I have no problems as of yet in there use. All loads at around 850 to 900 by the reloading books.  I dont order over the internet so I  buy local , its what they have its what i use. No leading in marlin 1894 357 that I can see, 25-2 s& w revolver,very good need to use 454 size bullits to get great groups,. Loads well  44 marlin 1894 none. I  will continue to use them . Loads well , nice uniform bullits
Logged

Offline Skillet

  • Trade Count: (1)
  • Member
  • *
  • Posts: 79
Re: Laser Cast Bullets?
« Reply #2 on: April 13, 2010, 08:46:16 AM »
I got leading with .44 spl handloads. Bad leading.

Threw the last of them into the casting pot and went back to making my own again.

Wheel weights and bar solder, 9 to 1 and no more leading...

Skillet
Logged

Offline Autorim

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 610
  • Gender: Male
Re: Laser Cast Bullets?
« Reply #3 on: April 15, 2010, 04:13:07 PM »
I have used and continue to use Lasercast bullets in .38, .357, .44 special and mag, .45AR and .45Colt. These bullets perform well in all firearms I have tested.
Logged

Offline walks with gun

  • Trade Count: (0)
  • Member
  • *
  • Posts: 40
Re: Laser Cast Bullets?
« Reply #4 on: April 20, 2010, 08:53:06 AM »
    I've used the .428 .240gr.  at around 1000fps and really liked them.
Logged
Pages: [1]   Go Up
« previous next »