Author Topic: 454 Casull Reamer Available for Rent (Read 4166 times)

quickdtoo · « **on:** December 03, 2010, 06:25:51 AM »

One of our member, geezer56, is generously donating a 454 Casull rifle chamber reamer to rent to GBO members, he'll be sending it to me as soon as he does his barrels, Bill (Graybeard) has given his Ok, so if anyone wants to rechamber their 45 Colt Carbine to Casull, PM me your name and address and I'll start a list, terms are the same as with the 357 Max reamer.

A big thank you to geezer56 for this offer!!

Tim

There are good instructions in the FAQs, just never turn the reamer backwards, always turn it clockwise in the cutting direction and use lots of cutting oil, it doesn't hurt to remove the reamer every few turns to clean the cuttings off with a soft brush, and go slow keeping the reamer inline with the bore, mounted vertical in a bench vice is the easiest way to do that, don't use the ends of the reamer handle for torque, try to turn it from as near the center as possible, the last two I did I used a nut driver and a 3/8" square drive socket so I'm just twisting the reamer and I'm less likely to end up cutting an egg shaped chamber by too much side force.

Please ship it back to me in a small flat rate priority box , cost will be a $5.80, be sure to use lots of tape to seal it up and include the original packing, some folks reuse the box, some use a new box, just depends on how it gets handled by the PO before they receive it. Include $20 cash(more is Ok too

), check, postal money order, all funds over my shipping cost from each rental will be donated to GBO.

S.E.Ak · « **Reply #1 on:** December 03, 2010, 09:25:55 AM »

After you

LONGTOM · « **Reply #2 on:** December 03, 2010, 10:47:37 AM »

I already have a 454.
Now if someone does the same with a 460 S&W I will be inline for that!

LONGTOM

cwlongshot · « **Reply #3 on:** December 03, 2010, 12:54:59 PM »

Quote from: quickdtoo on December 03, 2010, 06:25:51 AM

One of our member, geezer56, is generously donating a 454 Casull rifle chamber reamer to rent to GBO members, he'll be sending it to me as soon as he does his barrels, Bill (Graybeard) has given his Ok, so if anyone wants to rechamber their 45 Colt Carbine to Casull, PM me your name and address and I'll start a list, terms are the same as with the 357 Max reamer.

A big thank you to geezer56 for this offer!!

Tim

Geezer56, BIG THANK YOU!!!!

I already have a 454 from a Handi CR and LOVE it!! This will make many guys happy!!!

Happy Holidays to all,

CW

AtlLaw · « **Reply #4 on:** December 03, 2010, 02:37:15 PM »

Quote from: cwlongshot on December 03, 2010, 12:54:59 PM

Geezer56, BIG THANK YOU!!!!

I'll third that Geezer!

It's members thinking of other members and supporting the site that makes GBO what it is!

But... Tell me fellers... $:-\$ I gotta 45 Colt carbine and a 45-70 wearing carbine wood. I know nothing about the 454.

Does it fit a nich between those 2 cartridges?

dpe.ahoy · « **Reply #5 on:** December 03, 2010, 03:58:46 PM »

Sure does Richard, might come closer to the factory 45-70 loads than you think.

I might do it, but have 2 Rossi 454 Casull levers already. 'Course "need" never had anything to do with "want" when it comes to me and guns.

DP

krod47nw · « **Reply #6 on:** December 04, 2010, 02:43:11 PM »

Tim,

Please put me on the list for the 454 reamer. A big thanks to geezer56 for donating it. The great people here are what makes it such a great site.

PM sent with info....

geezer56 · « **Reply #7 on:** December 06, 2010, 06:29:19 AM »

quick, the reamer will start on it's way to you tomorrow. I did my 3 yesterday, took all of 30 minutes. Just for info, guys, this reamer is made for a rifle. It has a real leade section, like any bottleneck cartridge. It does NOT have the forcing cone arrangement like the SAAMI spec reamers do that are made for revolver use. Use lots of oil, clean frequently, and don't go too deep! It takes less time and force than you will believe. Thanks for all the kind words, guys. I've used this forum to answer a lot of questions, learn a lot, and sell, buy and trade handi rifle parts. Most of my handi herd has come through here, a piece at a time. This is somthing I can do to give back a little bit, in payment of what I've gotten from here. Danny, the geezer

quickdtoo · « **Reply #8 on:** December 06, 2010, 06:43:19 AM »

Thanks Danny, I might just have to buy another carbine barrel just so I can have a Casull!!

Tim

6x6 elk · « **Reply #9 on:** December 07, 2010, 11:34:10 AM »

What kind of accuracy are you guys seeing in your 454s, and what bullets are shooting the best with the Handi-rifle barrels? Thanks.

cwlongshot · « **Reply #10 on:** December 07, 2010, 12:41:59 PM »

Mine shoots easily into 2" at one hundred yards with its preferred loads. SO far I have only fired about 6 different powder and bullet combo's.
Here is a 50 Yard target I shot just after rechambering. Disregard bottom holes. There are five holes in the center:

The 300 XTP MAG and Gold Dot 454 bullets are good as is the 200 and 250 Hornady FTX bullets. As for pref on game, thus far only a 40# Coyote has been harvested. That was with a 200 FTX, very large exit so this bullet at just over 1900 may be fragile.

BUT, I have harvested over a dozen with my 45 COLT loaded to about 454 ballistics when fired from a hand gun and the 300 Speer, 300 XTP and 300 Sierra are favorites. Of those the 300 Sierra is my favorite.

CW

EDIT to add picture.

quickdtoo · « **Reply #11 on:** December 08, 2010, 07:42:52 AM »

Danny shipped the reamer to me today, so I should get it Friday, I should get it out in the mail to S.E.AK on Saturday.

Tim

S.E.Ak · « **Reply #12 on:** January 03, 2011, 10:45:26 AM »

Took about three turns on my barrel and it was done.Shoots a little than it did with 45colt and now the 45colt seems to even shoot better.There is a bit of a recoil jump with the full bore 454

krod47nw · « **Reply #13 on:** January 05, 2011, 06:53:15 PM »

I just got done reaming my barrel. This required even less reaming than the 357 max did. I only had to ream about the depth of the rim cut. Simple.

A big THANK YOU!!

to Geezer56 for donating this reamer, and to Tim for managing it's shipment.

Kevin

quickdtoo · « **Reply #14 on:** January 10, 2011, 11:09:43 AM »

Reamer went out to 26-t today, Bobby(revbc) is up next!

Tim

quickdtoo · « **Reply #15 on:** January 18, 2011, 11:51:38 AM »

The reamer went out today to Bobby!

There's no one else waiting, let me know if you're interested.

Tim

oldfort · « **Reply #16 on:** January 26, 2011, 04:40:06 PM »

I am waiting for the reamer. The Classic Carbine is on the way. Two boxes of .454 300gr arrived today with the Marbles Bullseye peep sight. When the rifle arrives, I will measure for the Kick Killer lace leather pad from Cabela's and a leather sling. Any advice on the pad size or sling is appreciated. Life is good.

yukondog · « **Reply #17 on:** February 05, 2011, 07:04:28 PM »

Tim I would like to be next in line. PM sent.

quickdtoo · « **Reply #18 on:** February 05, 2011, 08:13:43 PM »

Ok, gotcha on the list, just one ahead of you, oldfort should have received it today, but the PO didn't deliver it for some reason, he should have it Monday tho.

Tim

yukondog · « **Reply #19 on:** February 06, 2011, 11:28:53 AM »

Thanks, been thinking about it for awile now.

oldsoldja · « **Reply #20 on:** February 13, 2011, 11:38:22 AM »

Id like to be next in line for the reamer Tim.

quickdtoo · « **Reply #21 on:** February 13, 2011, 01:09:58 PM »

Ok, oldfort has the reamer now, hopefully done and on the way back, he got it on the 7th. Yukondog and revbc are next on the list before you.

Tim

6Covered · « **Reply #22 on:** February 14, 2011, 04:13:07 AM »

Tim -

Would you be so kind as to add me to the list?

Thanks,

Jon

quickdtoo · « **Reply #23 on:** February 14, 2011, 05:00:39 AM »

PM me your name and address.

Tim

beebzbarn · « **Reply #24 on:** March 17, 2011, 04:16:04 PM »

Hi, would it be possible to use it north of the border too (with applying ship fees of course!)

quickdtoo · « **Reply #25 on:** March 17, 2011, 04:33:22 PM »

I'll have to check it, I'll let ya know.

Tim

garbhead · « **Reply #26 on:** March 18, 2011, 01:27:03 PM »

A dumb 2-part question:

1. Could this be used on the 45/410 barrel without disastrous results and

2. Could this be used on my Judge 45/410 pistol?

quickdtoo · « **Reply #27 on:** March 18, 2011, 01:48:21 PM »

I don't think there's any point, the chamber should already be big enough to chamber a Casull round, but wouldn't be safe to fire due to the pressure involved and the mild steel the 45/410 barrel is made of.

Tim

DukeInMaine · « **Reply #28 on:** October 04, 2011, 03:51:15 PM »

I have my 45 LC barrel fitting coming back from H&R, and it's time for the reaming to 454 casull. PM coming. Thanks.

poncaguy · « **Reply #29 on:** October 17, 2011, 10:54:34 AM »

I'd like to rent the 454 Casull reamer, traded my 460 15" barrel..........so , no need to go that way, have a lot of 454 ammo though