Author Topic: 3 quoins needed  (Read 826 times)

0 Members and 1 Guest are viewing this topic.

Offline onegreatshot

  • keep their heads down til help arrives
  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 171
  • Gender: Male
  • Proud owner of 3 brooks USA cannons, look'g 4 more
3 quoins needed
« on: August 30, 2012, 01:27:29 PM »
I have 3 B/P Cannons all Brooks made. I'm in need of coins (sp) for the carriages. Anybody make then???  One id 50cal. the next is 69cal. and the last 1 in. bore. Please advise, have neither tools or area to make these. That's what living in So. Cal. does to you.

Offline one thumb short

  • Trade Count: (0)
  • Member
  • *
  • Posts: 62
Re: 3 coins needed
« Reply #1 on: August 30, 2012, 02:50:34 PM »
PM SENT

Offline Double D

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 12609
  • SAMCC cannon by Brooks-USA
    • South African Miniature Cannon Club
Re: 3 coins needed
« Reply #2 on: August 30, 2012, 03:06:23 PM »
I have 3 B/P Cannons all Brooks made. I'm in need of coins (sp) for the carriages. Anybody make then???  One id 50cal. the next is 69cal. and the last 1 in. bore. Please advise, have neither tools or area to make these. That's what living in So. Cal. does to you.

Coins is a good word to use to describe what you want when you aren't sure of the term. You are looking for quoins, said like coins except with a Q.  Did you contact Zulu?



Offline Zulu

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2477
  • Honor is a gift a man gives himself.
    • Wood & Ironworks
Re: 3 coins needed
« Reply #3 on: August 30, 2012, 03:22:33 PM »
DD,
Very good!  I couldn't figure out what he wanted.
Zulu
Zulu's website
www.jmelledge.com

Offline Double D

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 12609
  • SAMCC cannon by Brooks-USA
    • South African Miniature Cannon Club
Re: 3 coins needed
« Reply #4 on: August 30, 2012, 03:47:39 PM »
Here is one for the 8 inch siege howitzer.



If I can get the measurement from the rimbase to carrige bed  Ishould be able rescale this drawing for each gun.

Offline Doc Brown.

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 442
Re: 3 coins needed
« Reply #5 on: August 30, 2012, 07:00:19 PM »
I have 3 B/P Cannons all Brooks made. I'm in need of coins (sp) for the carriages. Anybody make then???  One id 50cal. the next is 69cal. and the last 1 in. bore. Please advise, have neither tools or area to make these. That's what living in So. Cal. does to you.

Just curious. Did you put wheels on the carrige?

Offline onegreatshot

  • keep their heads down til help arrives
  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 171
  • Gender: Male
  • Proud owner of 3 brooks USA cannons, look'g 4 more
Re: 3 Quoins needed
« Reply #6 on: August 31, 2012, 10:03:22 AM »
Double D, thanks for the update on the proper way it is to be spelled. I did put a question mark at the end because I was unsure. If it hadn't been for a video on this web site I would  of not known what they were called at all. All I knew it was an angled piece of wood under the breech for purposes of elevation.Double D, I will PM you with the information you requested on carriage sizes. If you are familiar with Brooks Cannons you will know the size of the Carriages. And Doc, yes The carriages I have do have wheels on them. As a matter of fact I sent one carriage back to Irishman (Mike) to have Brass wheels put on a smaller 50cal. carriage. It should look very nice when he has completed it. 

Offline cannonmn

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 3345
Re: 3 quoins needed
« Reply #7 on: August 31, 2012, 11:08:51 AM »
Wasn't there a popular song in the '60's about that, "Three Quoins in a Fountain?"

Offline Double D

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 12609
  • SAMCC cannon by Brooks-USA
    • South African Miniature Cannon Club
Re: 3 quoins needed
« Reply #8 on: August 31, 2012, 11:16:19 AM »
I have a vague familiarity of Brooks guns,   New SAMCC barrel  :)

Offline onegreatshot

  • keep their heads down til help arrives
  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 171
  • Gender: Male
  • Proud owner of 3 brooks USA cannons, look'g 4 more
Re: 3 quoins needed
« Reply #9 on: August 31, 2012, 12:54:57 PM »
Double D if that one in the picture being held by Michael is yours, your a lucky man a #1. Mine is stamped 2011. Hoping that is the year made.

Offline Double D

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 12609
  • SAMCC cannon by Brooks-USA
    • South African Miniature Cannon Club
Re: 3 quoins needed
« Reply #10 on: August 31, 2012, 04:48:23 PM »
Double D if that one in the picture being held by Michael is yours, your a lucky man a #1. Mine is stamped 2011. Hoping that is the year made.

For Micheal's sake I hope that is the serial number.

Mine is the SAMCC gun with the Standard muzzle flare.