« previous next »
Pages: [1]   Go Down

Author Topic: 10/22 mags  (Read 635 times)

0 Members and 1 Guest are viewing this topic.

Offline Rimfirekid1022

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
10/22 mags
« on: August 20, 2005, 01:32:00 PM »
this weekend i was at our hunting place in mississippi. i was shooting my 10/22 17 mach 2 conversion. it has always cycled great and still does. i think ive only had 2 jams and ive got about 750 rounds through it! but this weekend after about 150 rounds the bullets in the little rotary thing would catch on the side of the magazine and wouldnt rise up to the top to be loaded into the chamber. it would usually only happen on the 7th shot in the mag. and i would have to take the mag. out and smack it on the side hard to get the rotary with the bullet unstuck from the side of the clip and to come up to the top of the clip.it was not the guns fault at all because when it wouls happen the chamber would be closed and ready and when id pull the trigger, "Click". the bullet was stuck in the magazine and wasnt at the top to be loaded. is there any way i can clean the mags without taking them apart? last time i tried to take one apart and clean it i couldnt get it back together and had to throw it away. any suggestions appreciated!
joseph
Logged
Where'd ya learn that rookie??...Drug School??~Farva

Offline Omaha-BeenGlockin

  • Moderator
  • Trade Count: (0)
  • A Real Regular
  • *****
  • Posts: 864
10/22 mags
« Reply #1 on: August 25, 2005, 05:08:45 AM »
Taking the mags apart isn't that big of a deal.

IIRC---there are directions how to reassemble them right in the owners manual-----i give mine a little extra wind up on the spring for more positive function.
Logged

Offline kudzu

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 590
  • (Dancoman)
10/22 mags
« Reply #2 on: August 25, 2005, 04:17:16 PM »
breakfree-breakfree-breakfree- GOOD STUFF
Logged

Offline Rimfirekid1022

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
10/22 mags
« Reply #3 on: August 27, 2005, 02:30:47 PM »
Quote from: dancoman
breakfree-breakfree-breakfree- GOOD STUFF

what?????
Logged
Where'd ya learn that rookie??...Drug School??~Farva

Offline BlkHawk73

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1501
  • Gender: Male
10/22 mags
« Reply #4 on: August 27, 2005, 05:09:05 PM »
Quote from: Rimfirekid1022
Quote from: dancoman
breakfree-breakfree-breakfree- GOOD STUFF

what?????




http://www.break-free.com/?location=/products/index.asp
Logged
"Never Surrender, Just Carry On."  - G.S.

Offline mag shooter

  • Trade Count: (0)
  • Member
  • *
  • Posts: 46
10/22 mags
« Reply #5 on: September 11, 2005, 03:57:29 PM »
Tighten the hex nut as tight as you can with your fingers, then tighten the through bolt tight. Now back off the through bolt about an 1/8 turn, if you watch the rotor carefuly you will see it move slightly. This has been the perfect setting for all of mine , as for cleaning your choice of solvents followed by compressed air!!!!

Ps do not lube after cleaning!!!!!!!!!!!!!!!!!!!!!
Logged
Speak the TRUTH or say nothing at all!!!
Pages: [1]   Go Up
« previous next »