« previous next »
Pages: [1]   Go Down

Author Topic: re: Lee factory crimp die  (Read 531 times)

0 Members and 1 Guest are viewing this topic.

Offline Type99

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 107
re: Lee factory crimp die
« on: March 18, 2005, 12:28:13 AM »
Hello...

I purchased a 3-die set of Lee dies for the .303 British cartridge.  I have not used them yet.  

Theoretically, I would guess that the Factory Crimp Die for the .303 British would work for the 7.7 Jap cartridge, which I also reload for.  Can I use the crimp die for both these cartridges?  Anyone with the relevant experience?

Thanks much,
Gary
Logged

Offline jgalar

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1231
  • Gender: Male
re: Lee factory crimp die
« Reply #1 on: March 18, 2005, 01:37:53 AM »
I doubt that it would work, but if you don't mind possibly ruining a jap case give it a try. I would back the die out so you are not resizing all the neck, be carefull you don't get into the shoulder. As I recall Lee charges $50 for a custom made collet die set.
Logged

Offline PA-Joe

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 980
re: Lee factory crimp die
« Reply #2 on: March 18, 2005, 01:44:01 AM »
If you are only talking about the FCD it may work. Do both cases have the same length and neck shape? You will have a problem if one is longer than the other.
Logged

Offline jh45gun

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4992
re: Lee factory crimp die
« Reply #3 on: March 18, 2005, 08:23:38 AM »
I have read on the web lately that some folks use a washer as a spacer for using a other FCD. I the case I read it was using a 7.62x54 FCD for the 7.5x 55 Swiss. Since the Jap case is longer than the 303 the washer method may work. I have never tried it but it was reported it works. I guess the only way to know is to try it. Jim
Logged
Said I never had much use for one, never said I didn't know how to use it.

Offline Bug

  • Trade Count: (2)
  • Contributor
  • ***
  • Posts: 322
re: Lee factory crimp die
« Reply #4 on: March 19, 2005, 12:59:28 AM »
Jim,
I did something similar. I picked up a FCD for the WSM case cheaply, and shortened the bottom of the sliding part for use on the RSAUM case. It worked perfectly. I haven't yet tried the short die/washer thing... Yet. I think it should work, but it seems like it would be extreemly S - L - O - W. Where possible, I'll stick to shortening the collet, or bite the bullet, and spring for the $25 custom FCD. It won't break the bank, but is still a PITA.
Logged
It's The Little Things That Matter.

Offline jh45gun

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4992
re: Lee factory crimp die
« Reply #5 on: March 19, 2005, 08:56:07 AM »
From what the guy said when you put the brass in the shell holder you just slide the washer over the brass as you are doing it yea a extra step but until you bought the right FCD it would work. Jim
Logged
Said I never had much use for one, never said I didn't know how to use it.
Pages: [1]   Go Up
« previous next »