Author Topic: Ejector or Extractor?  (Read 493 times)

0 Members and 1 Guest are viewing this topic.

Swampman

  • Guest
Ejector or Extractor?
« on: September 06, 2006, 01:58:13 PM »
Which is better in your opinion.  My new handi will toss a loaded .45-70 round 6 feet.  Is the fired brass kicked out with equal vigor?

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Ejector or Extractor?
« Reply #1 on: September 06, 2006, 02:15:28 PM »
Which is better? Define better! An ejector, when it works like it was intended, is great for hunting, not so great at the range when you either need to police your brass, or you want to keep it to reload, then it requires a technique to catch it on opening of the action. An ejector that fails to work when hunting can be real unfortunate if a follow up shot it needed. Factory extractors don't fail, they are mechanical and very positive, but not as fast for reloading. It's a matter of preference, most prefer ejectors, but it's going to become a moot point, the factory will eventually not offer ejectors at all.

10 feet for empty brass, or an eye put out!! :o

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Roudy

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 206
Re: Ejector or Extractor?
« Reply #2 on: September 06, 2006, 02:23:09 PM »
Since everyone has their own opinion....here's mine.  If the rifle shoots cases that I reload I would prefer, extractors but if the rifle uses a cartridge that I don't reload for, then ejectors.  All of my H&R's and NEF's have ejectors, I've just learned to put my left hand ove the chamber area when I open the breech.

Roudy

Offline Datil

  • GBO Supporter
  • Trade Count: (17)
  • Senior Member
  • *****
  • Posts: 1822
  • Gender: Male
Re: Ejector or Extractor?
« Reply #3 on: September 06, 2006, 02:33:17 PM »

 * to 10 feet that is nothing My 219 Zipper toss load rounds 12 feet,
 And into cacyus if there is one handi! Marv.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Ejector or Extractor?
« Reply #4 on: September 06, 2006, 02:59:12 PM »
Again, SEE THE FAQ and HELP STICKY!!!!!!!!! ::)

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Ejector or Extractor?
« Reply #5 on: September 06, 2006, 03:43:44 PM »
Shame on you, that means you didn't read all of it! It's down near the bottom of the page. ;)

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Ejector or Extractor?
« Reply #6 on: September 06, 2006, 04:43:33 PM »
Maybe your wife can show you that TC 1:48" barrels actually do shoot round balls good!! ;D

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline jack19512

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 639
Re: Ejector or Extractor?
« Reply #7 on: September 07, 2006, 01:06:28 AM »
  If the rifle shoots cases that I reload I would prefer, extractors but if the rifle uses a cartridge that I don't reload for, then ejectors. 





+1   :)

Offline Dillohide

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 273
  • Gender: Male
Re: Ejector or Extractor?
« Reply #8 on: September 07, 2006, 04:51:15 AM »
Have yet to have the Extractor fail me with reloaded 30-06 brass. Cannot say the same for the Ejector in .223 and 30-30. The Extractor is slower and will take some getting use to grabbing a rimless case while wearing hunting gloves but would rather have a sure thing under hunting conditions. So, I like the Extractor.