« previous next »
Pages: [1]   Go Down

Author Topic: Topper Shotgun Bead Sight Size  (Read 1844 times)

0 Members and 1 Guest are viewing this topic.

Offline GrampaMike

  • GBO Supporter
  • Trade Count: (3)
  • A Real Regular
  • *****
  • Posts: 904
  • Gender: Male
Topper Shotgun Bead Sight Size
« on: September 18, 2006, 10:57:45 AM »
Hello,
Does anyone know the thread size and length of the Topper Shotgun front bead sight?
Or where I could buy schematics of H&R/NEF Rifles/Shotguns.
Thanks guys, Mike
Logged
Grampa Mike
U.S. Army Retired

"Say what you mean, mean what you say"
Father of 2 GREAT sons, and 9 grandchildren.

Offline Cookiemann

  • Trade Count: (9)
  • Senior Member
  • *****
  • Posts: 1749
  • Apple Valley, MN
Re: Topper Shotgun Bead Sight Size
« Reply #1 on: September 18, 2006, 11:24:24 AM »
GrampaMike,
Check out this link, it should get ya the schematics for free.  Can't remember about the bead-thread size, but I am sure I have seen it around the forum here somewhere.  Good Luck...here's the link:
http://www.e-gunparts.com/model.asp?idDept=101

cookiemann
Logged
NOT ON MY WATCH

"AIM small...MISS small"

Offline lotus

  • Trade Count: (5)
  • Member
  • *
  • Posts: 68
Re: Topper Shotgun Bead Sight Size
« Reply #2 on: September 18, 2006, 12:09:19 PM »
i believe they are 3-56.

Its been a while since I have changed mine, but that number sticks in my mind.
Logged

Offline Markus

  • Moderators
  • Moderator
  • Trade Count: (15)
  • Senior Member
  • *****
  • Posts: 1767
  • Gender: Male
Re: Topper Shotgun Bead Sight Size
« Reply #3 on: September 18, 2006, 02:12:57 PM »
Lotus is correct. At least thats the listed size for current production.
Logged
PROUD REDNECK CONSERVATIVE

I'd much rather be remembered for being a great shot than having the most expensive gun

Offline tfranklin7

  • GBO Supporter
  • Trade Count: (163)
  • Contributor
  • *****
  • Posts: 408
  • Gender: Male
Re: Topper Shotgun Bead Sight Size
« Reply #4 on: September 19, 2006, 02:21:42 AM »
Its a 3-48, The only replacement I could find was -part #446-001-348     3-48 Raybar Shotgun Sight     www.brownells.com
Hope this helps.   Tony



6-48 TPI   Remington/Ithaca/SKB

5-40 TPI    Mossberg

3-56 TPI   Browning Target Citori, Beretta, Kreigoff, Ruger, Weatherby, Winchester, Marlin, Stevens 311, H&R

M3.0-.5    Browning Gold, Citori Field, Franchi, H&K, Fabarm

M3-.6   Browning Citori Hunter

5-44 TPI  Browning BPS

M2.5-.45   S&W

3-48 TPI  New England Firearms

M2-6 will interchange with a 3-56 TPI
Logged
"A government big enough to give you everything you want, is big enough to take away everything you have." - Thomas Jefferson

Offline GrampaMike

  • GBO Supporter
  • Trade Count: (3)
  • A Real Regular
  • *****
  • Posts: 904
  • Gender: Male
Re: Topper Shotgun Bead Sight Size
« Reply #5 on: September 19, 2006, 08:30:05 AM »
Thanks guys,

I knew there would people here with the answer.
I think between everyone here, we know everything. ;D

Tony went the extra mile with all of his info, hard for me to type that much.

Printed off the whole Thread, will start looking again for my replacement.

Thanks again, Mike
Logged
Grampa Mike
U.S. Army Retired

"Say what you mean, mean what you say"
Father of 2 GREAT sons, and 9 grandchildren.
Pages: [1]   Go Up
« previous next »