Author Topic: H&R WISH LIST (Read 46915 times)

jwinva · « **Reply #90 on:** November 05, 2006, 02:48:59 PM »

Additions to combo offerings of .243/blackpowder.Nothing wrong with the .243 but some would like .30/06,.280,.270.7mm/08,.308.

Fazak · « **Reply #91 on:** November 06, 2006, 06:16:00 AM »

I doubt that it will ever happen, but a Handi chambered in 6X45 (.223 with neck expanded to 6mm) would be a very interesting and useful chambering to play with. The 6X45 started life as a very easily made wildcat chambering for bench rest competition. It's a very efficient chambering which can approach 2700 fps with a 90 grain bullet. It's also known for providing long barrel life.

rain164845 · « **Reply #92 on:** November 08, 2006, 02:55:27 PM »

Is a 9mm Luger chambered Handi. I can't think of a better plinker and flinch trainer with more whap factor than a .22. Cheap ammo, I just wonder if it has the recessed primer problem of the 7.62 x 39 since it is primarily loaded for semis to reduce slamfires. Are you listening Marlin? I need a 9mm barrel for Christmas!

Joe

perklo · « **Reply #93 on:** November 09, 2006, 04:22:52 AM »

My list is pretty Simple:

1) A RIMMED cartridge to be developed by Marlin/H&R that has 30.06+ level performance (30 cal., 180-220 gr. bullets at close to 3000 fps) to make the design a single-shot, long-range big game gun. Likely based (like Elmer Keith's wildcat for single and double rifles) on Euro 9.3x74R brass. With the Handi design, rimmed is just flat more reliable...

2) A high-end rifle with the metal hardware and the special-run grey laminate checkered stocks.

3) On this high-end rifle, add the much desired low profile hammer and WELD a scope rail on.

4) A 24" standard profile barrel, to get the most out of the cartridge without being as front heavy as 26" guns.

5) Roll ALL the above into a single gun!

- perklo

canon6 · « **Reply #94 on:** November 09, 2006, 05:06:42 AM »

I would like 6.5 dia NEF,something like 6.5X30-30,I want a 125gr NBT at 2700-2800,24inch barrel steel hardware Doug

knight0334 · « **Reply #95 on:** November 11, 2006, 09:28:18 AM »

1. For them to make another batch of steel trigger guards and forearm spacers.
2. A factory custom shop with blank chambers so we can order a cartridge in what ever flavor we wanted - given workable pressures and twistrates for our selected cartridge.
3. More 24" and 26" barreled rifles.
4. 1-in-18" or 1-in-20" twist 44mag/444Marlin barrels that slug to .428-.429"
5. More rimmed cartridges{insert personal opinion= rimless are for autoloaders and boltguns}{/end opinion}
6. A rounded hammer instead of the squared stock steel(custom shop option)
7. Extra fancy walnut or other fine wood options on the custom rifles.

SBG · « **Reply #96 on:** November 15, 2006, 07:31:16 AM »

I would like to see a double barrel.

New calibers that I would buy are .260 Rem and .257 Roberts

hmt · « **Reply #97 on:** November 15, 2006, 02:15:07 PM »

I would like a tracker II with an 18.5" barrel and ghost ring sights ...

OBXPilgrim · « **Reply #98 on:** November 17, 2006, 01:58:34 PM »

I know this thread is getting old, but I just couldn't stand it any more. Hopefully, somebody at H&R/NEF reads these & might realize they could PROFIT from some of these suggestions.

Since Hornady started loading 9.3x74R - how 'bout a Handi in that!! Better yet, make it a EURO/AFRICAN CLASSIC along the same lines as a BC - 26" to anything up to 30" barrel. Those 9.3x74R cartridges look wicked!! I'd love to play with some cast bullet loads for that. I wouldn't even care that it wasn't a double rifle or drilling.

I, to would like a .44Mag with a .44Mag barrel (.429").

I like rimmed cases in Handi's, but any 6.5mm bore would float my boat as well.

Also, design a cartridge holder that has the same outside dimensions on the outside, cut out the center of the plastic/fiberglass buttstock, and make the cartridge holder snap into it. If all the boxes are the same outside dimension, the carrier will fit, no matter what barrel you switch to. If it's hinged - even better. I don't want to have to unscrew a bolt on the buttplate (Survivor), or stick a buttstock cartridge carrier made of black elastic cloth - I don't like having bullets sticking into my face if I switch shooting shoulders. The "Tamer" stock design is real close! Toss the .410 or 12 ga carrier & put in something that would work.

Headspace · « **Reply #99 on:** November 19, 2006, 02:50:00 AM »

I don't want them to change too much cause the main thing I like is the price. But I really NEED a barrel chambered for the new Federal 338.

elkslayer4x5 · « **Reply #100 on:** November 20, 2006, 05:48:42 AM »

I would like to see more finish options, more barrels in stainless, rifle and shotgun, stainless trigger guards and spacers, also more barrells for the TDC, like 16 ga, 28 ga and .410 bore all with vent rib

guimus · « **Reply #101 on:** November 24, 2006, 06:54:18 AM »

I'm late to this party, but I'll chime in with echoes of what some others have said:

Chamberings I'd love to see:
7.62x54R that will handle surplus ammo
.460sw or .454 casull

hunteraz · « **Reply #102 on:** November 24, 2006, 06:10:48 PM »

I would like a 26" 270 WSM!!!!!! hey this is a wish list so I am just wishing away!!

East TennesseChris · « **Reply #103 on:** November 25, 2006, 07:09:34 AM »

1. A smokeless muzzleloader.

2. this is the BIG ONE!!! A .50 BMG.

quickdtoo · « **Reply #104 on:** November 25, 2006, 08:45:33 AM »

There won't be either a .50BMG or a WSM, TC or Bullberry won't even chamber an Encore in any short mag caliber.

Tim

http://www.bullberry.com/message.html

9x19 · « **Reply #105 on:** November 29, 2006, 08:20:29 PM »

I didn't read alll four pages, so if these have already been mentioned...

.250 Savage

.338 Federal

FLNT4EVR · « **Reply #106 on:** December 21, 2006, 01:04:47 AM »

Definitely the 250-3000 .I've always wanted one.

krod47nw · « **Reply #107 on:** December 21, 2006, 04:23:15 AM »

I would like to see 7x57, 6mm Remington, 257 Roberts and 35 Remington.
I would also like more choices in stocks. maybe a high gloss walnut one.
A heavy duty model in some magnum calibers.

WeHuntTurkeys · « **Reply #108 on:** December 24, 2006, 12:02:16 PM »

With the marketing to women and youth in mind, here's a basic offering missing from an excellent line:
Youth Handi-Rifle frames (existing caliber choices) with a laminated wood or walnut hardwood stock (not Monte Carlo or Synthetic), that I can order 20 ga. and 12 ga. barrels for with screw in chokes (modified, turkey, etc.). Ported shotgun barrels optional.

wcf3030 · « **Reply #109 on:** December 24, 2006, 12:28:04 PM »

A 35 Whelen with a faster? twist rate for the bigger bullets.
Another vote for the 338 federal or 338 varient. 338-06

Mojo^ · « **Reply #110 on:** December 24, 2006, 03:43:46 PM »

An octagon barrel for the Buffalo Classic. Maybe a .45-110 or .50-110 in the same.

Daniel Laws · « **Reply #111 on:** December 25, 2006, 10:04:50 AM »

Octagon 30-30, BC, and 38-55 Target, with brass furniture. And add the 6.5X55, or it's clone, a 260 Rem. The option for a walnut MC stock would also be nice.

gould · « **Reply #112 on:** December 25, 2006, 02:06:34 PM »

I would like to have a handi in 7-30 and I would also like a 20 ga tamer in a blued finish. I know I should just be happy to grt it at all in a 20ga. but I really like the blued finish. I want one more thing a 44 mag that atleast has the right size bore. How hard is that one. You might even sell a few and have pepole be happy.

MSP Ret · « **Reply #113 on:** December 25, 2006, 03:03:56 PM »

I'd like to see H&R/NEF put a little more thinking onto some of thier decisions, this thing about the .44 Mags made with the wrong size bore is a real baffler. Why in the heck would someone authorize that error to begin with, and then when it was discovered why is it allowed to continue? Someone should have been at least spoken to about that glaring error, AND it should have been corrected immediately, but no, they allow it to continue!!! DUMB!!! and poor business practice....<><....

gstanfield · « **Reply #114 on:** December 26, 2006, 01:51:15 PM »

6.5X55!!!!!

Also, more 26" and 28" barrels please.

George

myarmor · « **Reply #115 on:** December 26, 2006, 02:26:59 PM »

So far it seems most of our wants are reasonable.

Right sized bores and twists.

Longer barrels for certain calibers.

Wider varity of stocks and barrel configs.

And expand, at least just a little, the caliber selection.

Sounds like one of the bigger reasons for none of this is the lack of space they work in. I haven't actually been to the factory, but it seems to me from all reports they need to upgrade!

10ga. · « **Reply #116 on:** December 26, 2006, 02:53:22 PM »

50 Alaskan!!

t-roy · « **Reply #117 on:** December 27, 2006, 07:55:00 AM »

ejectors!!

MTGlass · « **Reply #118 on:** December 29, 2006, 11:37:11 AM »

Just in case H&R is listening & looking for ideas for their 2007 line up...

I'd like to see the Youth Model Handi's offered in boxed set combos that have a .223 barrel included with the .243 and 7mm-08 offerings.

I have an SB2-Y08 on order for my daughter, but I'd have ordered the 7mm-08/.223 combo in a heartbeat.

Cordially,

MTGlass

Illhunter · « **Reply #119 on:** January 10, 2007, 06:22:09 PM »

i would like a 300 win mag in a handi and a 6.5swede and maybe a 7.5x55

Terry