« previous next »
Pages: [1]   Go Down

Author Topic: Red Dot Mounting on a Knight ML????  (Read 558 times)

0 Members and 1 Guest are viewing this topic.

Offline hamrhed

  • Trade Count: (0)
  • Member
  • *
  • Posts: 5
Red Dot Mounting on a Knight ML????
« on: November 15, 2006, 08:12:59 AM »
I would like to mount my red dot sight on my Knight Revolution II.  Problem is that the two piece rail mounts are spaced too far apart for the sight bracket.

Is there a one piece rail mount that lines up with a knight ML???

Has anyone ever run into this situation??? 
Logged

Offline SURVEYOR

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 209
Re: Red Dot Mounting on a Knight ML????
« Reply #1 on: November 15, 2006, 09:07:48 AM »
You just need one ring as far forward as you can get. They do make extended bases if you want 2 rings. But you don't need to look through a red dot as you would with a scope. Forward is better.
Logged
I''m A Dirty White Boy and I''m Proud Of It!

Offline hamrhed

  • Trade Count: (0)
  • Member
  • *
  • Posts: 5
Re: Red Dot Mounting on a Knight ML????
« Reply #2 on: November 15, 2006, 09:53:46 AM »
Surveyor,

The sight has a weaver style mount system (No rings). Its a clamping mech on the bottom.

The weaver mounting base is two pieces approx. one inch long each + or -. They are too far apart when attached to the taped holes on the gun.

Yes I want the sight mounted further up on the gun, but if attached to only the front mounting base (rail) it is only one inch long and attached to the guns receiver with only two screws...

That does not seem secure enough to hold the sight.
Logged

Offline SURVEYOR

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 209
Re: Red Dot Mounting on a Knight ML????
« Reply #3 on: November 15, 2006, 10:35:28 AM »
Logged
I''m A Dirty White Boy and I''m Proud Of It!

Offline hamrhed

  • Trade Count: (0)
  • Member
  • *
  • Posts: 5
Re: Red Dot Mounting on a Knight ML????
« Reply #4 on: November 15, 2006, 11:04:58 AM »
Surveyor,

If the hole patern on that mount is compatiable with my Knight, that is just what i'm looking for...

Could you give me more info on that part and where to get one...

Thanks alot
Logged

Offline Wolfhound

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 418
Re: Red Dot Mounting on a Knight ML????
« Reply #5 on: November 15, 2006, 11:37:29 AM »
hamrhed,
Knight doesn't have a 1 piece base for any of it's ML's and no one to my knowledge makes one for a Knight. I've reccomended they make one but so far they haven't done it. The only way to get a 1 piece mount is to have a gunsmith do it.
Logged

Offline SURVEYOR

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 209
Re: Red Dot Mounting on a Knight ML????
« Reply #6 on: November 15, 2006, 04:20:43 PM »
OK! Here some blank stock you can or have a gunsmith drill the holes for you. No they don't make one for a Knight, but why have that stop you!

http://www.brownells.com/aspx/ns/store/catsearch.aspx?c=1841&p=4805

http://www.midwayusa.com/esearch.exe/search?TabID=3&category_selector=all_products&search_keywords=gunsmith
Logged
I''m A Dirty White Boy and I''m Proud Of It!

Offline hamrhed

  • Trade Count: (0)
  • Member
  • *
  • Posts: 5
Re: Red Dot Mounting on a Knight ML????
« Reply #7 on: November 16, 2006, 03:53:18 AM »
Thanks Surveyor,

Your sugestion is what I'm going to do..

Thanks again for your input and help...

Chris...
Logged

Offline hamrhed

  • Trade Count: (0)
  • Member
  • *
  • Posts: 5
Re: Red Dot Mounting on a Knight ML????
« Reply #8 on: November 17, 2006, 03:30:38 AM »
Wolfhound & Surveyor

The gunsmith method is out he is a crotchitey old f**k with a major attitude.  >:(

Went with the standard Knight mounts and a new bushnell scope... done deal...

Thank you both for your help and info... Good hunting

Chris...
Logged
Pages: [1]   Go Up
« previous next »