Author Topic: Mould wanted - Lyman 323471  (Read 1414 times)

0 Members and 1 Guest are viewing this topic.

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Mould wanted - Lyman 323471
« on: March 21, 2007, 07:24:38 PM »
I'm trying to get my Swedish rolling block in 8 x 58R Danish Krag shooting.  I need a heavy cast bullet similar to the 215 gr. Lyman Loverin 323471.  Anyone have one for sale?

Offline Bitterroot Bob

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 249
Re: Mould wanted - Lyman 323471
« Reply #1 on: March 22, 2007, 03:09:20 PM »
Howdy,
That's liable to be a tough one to find. I'd try eBay.com first and be patient. That number shows up from time to time. I'd sell mine, but the other cavity in the block is a 321297- a 185-grain FN that I shoot out of a .32 Special Winchester 94. You might try bullets designed for the .32-40 or the Special. There are some long heavy ones out there and you might find a suitable mould quicker.

Good luck,
Bitterroot

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: Mould wanted - Lyman 323471
« Reply #2 on: March 22, 2007, 04:46:57 PM »
Yeah I know.  Too bad Lyman dropped it, it is so useful for 8 x 57's and now I have an 8 x 58RD.  I do have a 190 gr. Hoch nose-pour for my .32-40 Schuetzen (Ruger #3)  It will have to do until one surfaces.

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: Mould wanted - Lyman 323471
« Reply #3 on: June 04, 2007, 05:30:22 AM »
Still lookin'  Anyone have a contact with Lyman?

Does anyone still make a similar mould?

Offline Blammer

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 238
Re: Mould wanted - Lyman 323471
« Reply #4 on: June 09, 2007, 04:51:26 PM »
over on Cast boolits . com there is the possibility of a group buy for a 180 gr 8mm flat point bullet. cost probably about $100 or so.

You may want to check it out.

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: Mould wanted - Lyman 323471
« Reply #5 on: June 14, 2007, 05:27:41 AM »
I think I'll stick with the 190gr. HOCH nose-pour, for now.  Thanks for the tip, and I am still looking for a 323471

Offline WILDCATT

  • Trade Count: (0)
  • Member
  • *
  • Posts: 60
Re: Mould wanted - Lyman 323471
« Reply #6 on: June 15, 2007, 10:09:29 AM »
the cast bullet site gets lee molds.the $100 is setup.the molds cost Lees regular price.they have to get 20 orders and the 100 is waved.

Offline Blammer

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 238
Re: Mould wanted - Lyman 323471
« Reply #7 on: June 16, 2007, 04:45:49 PM »
GENERALLY at the Cast boolit site.....


the 8mm mould I was referring to was not going to be a lee mould it was not going to be an aluminum mould and the $100 was going to be the total cost for one copy of the mould.


Offline gutshot_again

  • Trade Count: (7)
  • Member
  • *
  • Posts: 96
Re: Mould wanted - Lyman 323471
« Reply #8 on: June 25, 2007, 05:12:53 AM »
Bitterroot, I left you a PM.

Offline Bitterroot Bob

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 249
Re: Mould wanted - Lyman 323471
« Reply #9 on: July 27, 2007, 05:07:56 PM »
HEY!
Check ebay. There is a listing for a Lyman #320378 mould. It is a 243-grain (really) RN-GC. Check under "bullet mould" in the search. This might be more interesting than the 323471!

Bitterroot

Offline Bitterroot Bob

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 249
Re: Mould wanted - Lyman 323471
« Reply #10 on: August 01, 2007, 07:40:10 AM »
Sir Charles:
I hope that was you that bought the 320478 mould. 245 grains! Man, that would be like shooting a pencil.

Bitterroot

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: Mould wanted - Lyman 323471
« Reply #11 on: August 02, 2007, 01:48:01 PM »
No it wasn't.  I've never played on Ebay.  I heard you need a playpal to "do" it!  Now I hear that Ebay won't play guns anymore!

Offline Frank46

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 707
Re: Mould wanted - Lyman 323471
« Reply #12 on: September 24, 2007, 10:41:30 PM »
Check with midsouth shooter's, they normally have two 8mm molds made by lee, but they were designed by a gentleman from the cast boolits website. I believe that one is a heavy 8mm design. Hope this helps, regards, Frank

Offline Sir Charles deMoutonBlack

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 323
Re: Mould wanted - Lyman 323471
« Reply #13 on: September 27, 2007, 06:54:30 PM »
Thanks Frank;  I'll call midsouth.