« previous next »
Pages: [1]   Go Down

Author Topic: Dan Wesson Monson,MA Early production .44  (Read 2110 times)

0 Members and 4 Guests are viewing this topic.

Offline tiktock

  • Trade Count: (0)
  • Member
  • *
  • Posts: 11
Dan Wesson Monson,MA Early production .44
« on: November 12, 2007, 03:19:49 AM »
Hello,
I just purchased a Dan Wesson .44 Mag marked Monson,MA with a four digit serial number #0040XX.

I havent seen one this early in the serial number and was looking for a ballpark on age...Im guessing late 70's from a 5 digit i saw here that was made in 79.  Trigger stop is in frame.  Here are a few pics:

Logged

Offline Cayoot

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 156
  • Gender: Male
Re: Dan Wesson Monson,MA Early production .44
« Reply #1 on: November 13, 2007, 03:19:35 PM »
Beautiful!!!!! Just Beautiful!!!!!
Logged
Thanks from the Frozen Northwoods!!!

“For God so loved the world that He gave His only begotten Son, that whosoever believeth in Him should not perish, but have everlasting life” – John 3:16

That still amazes me…I don’t care who you are or how much I care about you, I would never let you kill my son.  I can’t even begin to understand how much He loves us.

Offline buffermop

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 946
Re: Dan Wesson Monson,MA Early production .44
« Reply #2 on: November 13, 2007, 05:50:00 PM »
It had to be in the late 70's or early 80's. Went down to the plant in Monson for a job interview in the mid 80's. Saw the line being manufactured. A truly fine piece of workmanship.
Logged

Offline tiktock

  • Trade Count: (0)
  • Member
  • *
  • Posts: 11
Re: Dan Wesson Monson,MA Early production .44
« Reply #3 on: November 14, 2007, 02:16:20 AM »
I've fed this badboy a steady diet of .44 mag rounds since purchase.  Ive put probably 300 rounds through it this week and it is one of the most accurate handguns I own.  The only issue i've had at all is the cylinder sticking in a few instances but I believe they were all due to simple grit getting into the ratchet grooves and I plan to apply some dry lube to that area to prevent grit from sticking in there....
Logged

Offline blhof

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 738
Re: Dan Wesson Monson,MA Early production .44
« Reply #4 on: November 15, 2007, 12:19:00 AM »
You might also check your barrel cylinder gap.  It should be .006, but you need to check all the gaps. The Monson and Palmer plants did all their cylinder milling in the soft then hardened; this sometimes resulted in a variance in the length of the cylinder, .002 was considered acceptable and you just set on the longest chamber.  I used to set it at .005 on the longest and it still gave 1" groups until I had the cylinder honed, when I had to bring it in for some trigger work.
Logged

Offline NailShooter

  • Trade Count: (0)
  • Posts: 3
Re: Dan Wesson Monson,MA Early production .44
« Reply #5 on: December 06, 2007, 01:40:01 AM »
Quote from: tiktock on November 14, 2007, 02:16:20 AM
........The only issue i've had at all is the cylinder sticking in a few instances but I believe they were all due to simple grit getting into the ratchet grooves......

I have owned 3 DW revos for about 27yrs (incl a 44 mag).  I like to run the cly to bbl gap on the tight side.  The binding you refer to has been 100% caused (on MY guns) by something getting in the gap.  Do not force the cyl to rotate by forcing the hammer back.  Check the gap setting as the other poster said and keep the faces of the cyl and bbl end clean.  Keep adjusting the gap  .001" wider until the problem stops.

Mine is accurate as all get out, too!

Nail 
Logged
Pages: [1]   Go Up
« previous next »