« previous next »
Pages: [1]   Go Down

Author Topic: Thank goodness for Midsouth.  (Read 630 times)

0 Members and 1 Guest are viewing this topic.

Offline PartsMan

  • GBO Supporter
  • Trade Count: (7)
  • Senior Member
  • *****
  • Posts: 1351
  • Gender: Male
  • Proud Handi Owner
    • myspace
Thank goodness for Midsouth.
« on: November 29, 2007, 04:10:03 AM »
After waiting since early October for my 7mm-08 case length gage from my gun shop,
I got on line and ordered one from Midsouth Shooters Supply.
Got it yesterday.:) :)

BTW I did cancel my BO with the gun shop and they were understanding.
Logged

Offline beemanbeme

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2587
Re: Thank goodness for Midsouth.
« Reply #1 on: November 29, 2007, 04:23:48 AM »
Don't know if it's a kinda same situation or not but I was having trouble getting a part for my outboard motor thru a local outfit.  Come to find out, they would wait to order from a jobber until they had enough "stuff" to make paying the freight worthwhile.  I called direct and got it a couple of days later.
Of course, the local guy was blaming the jobber, etc,etc, etc. 
Logged

Offline PartsMan

  • GBO Supporter
  • Trade Count: (7)
  • Senior Member
  • *****
  • Posts: 1351
  • Gender: Male
  • Proud Handi Owner
    • myspace
Re: Thank goodness for Midsouth.
« Reply #2 on: November 29, 2007, 04:39:40 AM »
I did see that another site showed low stock so I think the BO story is real.

The point is that Midsouth had it in stock so that didn't matter.
Logged

Offline skb2706

  • Trade Count: (5)
  • Senior Member
  • *****
  • Posts: 1428
Re: Thank goodness for Midsouth.
« Reply #3 on: November 29, 2007, 06:42:51 AM »
Just an observation...but wouldn't it have been easier to order a vernier caliper and not only had a tool that would do what you wanted but many other tasks as well. Everyone sells cheap digital calipers.
Logged

Offline cowboyup453

  • GBO Supporter
  • Trade Count: (82)
  • A Real Regular
  • *****
  • Posts: 685
  • Gender: Male
Re: Thank goodness for Midsouth.
« Reply #4 on: November 29, 2007, 07:46:58 AM »
Quote from: skb2706 on November 29, 2007, 06:42:51 AM
Just an observation...but wouldn't it have been easier to order a vernier caliper and not only had a tool that would do what you wanted but many other tasks as well. Everyone sells cheap digital calipers.
I think partsman is refering to the Lee guage. So if he dosent have a case trimmer(other than the lee one) the calipers wont help with his trimming. ;)
http://www.midsouthshooterssupply.com/item.asp?sku=0000690167
Logged

Offline skb2706

  • Trade Count: (5)
  • Senior Member
  • *****
  • Posts: 1428
Re: Thank goodness for Midsouth.
« Reply #5 on: November 29, 2007, 09:20:59 AM »
If you know the max length spec. of your cases....ie   2.045" and you set the venier to that dimension, lock it down. Any case that fits between the jaws is ok, any that don't need trimmed. At this point you don't have to have a trimmer but you will know which cases are out of spec. To me that makes more sense that a case length guage....which in 35 years of handloading I have never owned.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Thank goodness for Midsouth.
« Reply #6 on: November 29, 2007, 09:35:06 AM »
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline OR-E-Gun Bill

  • GBO Supporter
  • Trade Count: (18)
  • A Real Regular
  • *****
  • Posts: 907
  • Gender: Male
Re: Thank goodness for Midsouth.
« Reply #7 on: November 29, 2007, 10:04:48 AM »
Speaking of Midsouth, got this CHRISTmas Special in my e-mail today.



With a 60 mile round trip for me to the nearest town with reloading equipment and diesel fuel @  over $3.50 per gallon, it sure looks good to me!


Bill
Logged

Offline PartsMan

  • GBO Supporter
  • Trade Count: (7)
  • Senior Member
  • *****
  • Posts: 1351
  • Gender: Male
  • Proud Handi Owner
    • myspace
Re: Thank goodness for Midsouth.
« Reply #8 on: November 29, 2007, 04:46:15 PM »
I have calipers, dial and analog, all they told me is that I need to trim my cases.
Logged
Pages: [1]   Go Up
« previous next »