« previous next »
Pages: [1]   Go Down

Author Topic: MY 24 lb in action  (Read 854 times)

0 Members and 1 Guest are viewing this topic.

Offline rampa room artillery

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 580
MY 24 lb in action
« on: May 21, 2008, 05:30:14 PM »













my 24 lb confederate mortar in action at the spring nssa nationals.  17th out of 53 mortars   51 feet 1.5 inch
Logged

Offline cannonmn

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 3345
Re: MY 24 lb in action
« Reply #1 on: May 21, 2008, 08:28:59 PM »
Thanks for the pix.  I'll bet that's a steel mortar with no liners, isn't it?  There were quite a few "Confederate mortars" like that made up for NSSA members within about the past 10 years.
Logged

Offline dan610324

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2413
  • Gender: Male
  • bronze cannons and copper stills ;-))
    • dont have
Re: MY 24 lb in action
« Reply #2 on: May 22, 2008, 12:53:55 AM »
whats the measurements of those mortars ??

anyone having any drawings ??
Logged
Dan Pettersson
a swedish cannon maniac
interested in early bronze guns

better safe than sorry

Offline cannonmn

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 3345
Re: MY 24 lb in action
« Reply #3 on: May 22, 2008, 01:06:58 AM »
Quote
anyone having any drawings ??

Dan I can't draw for s__t but I can describe these pretty closely as far as outside is concerned.

Barrel is right-circular cylinder, hemispherical at breech end.  A steel bar the proper size and length for the trunnions is welded to the center of the hemisphere.  I'm not sure whether the hemisphere is machined out for the bar or not, it probably is to some extent.  As far as I know these are made from only two pieces of steel, the barrel bar and the trunnion bar.  Bore of a US or CS 24 pdr. is 5.82 inches.  I think these are also made in 12 pounder size.  I don't know what the chamber shape or dimension is.  This pattern is copied from one or two surviving CS (are you ready for this?) CAST IRON originals.  The Confederate States did not have steel to use, nor even bronze at that time, so they used what they had.  One of the originals is (or was) on a monument at Amelia Courthouse, Virginia, and is shown in various books on CW artillery.
Logged

Offline dan610324

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2413
  • Gender: Male
  • bronze cannons and copper stills ;-))
    • dont have
Re: MY 24 lb in action
« Reply #4 on: May 22, 2008, 03:23:32 AM »
CAST WHAT DID YOU SAY ???

oooohhh poop ##**^,;   uuaaäää
sorry dont understand that ugly word   ;D ;D ;D
Logged
Dan Pettersson
a swedish cannon maniac
interested in early bronze guns

better safe than sorry

Offline MR.GADGET

  • Trade Count: (0)
  • Member
  • *
  • Posts: 76
  • Gender: Male
Re: MY 24 lb in action
« Reply #5 on: May 22, 2008, 07:20:25 AM »
This is my 12 pound tube need to find one of it shooting. Did OK was 15th... We were 1st and 2nd in the past nationals.... and the cannons. scale 3" ord and 6 pound.


Logged
MR. GADGET
NRA LIFE BENEFACTOR MEMBER
www.nra.org
Co. D, 10th Regiment N.C.S.T. "Rowan Artillery"
www.n-ssa.org

Offline Tropico

  • GBO Supporter
  • Trade Count: (0)
  • A Real Regular
  • *****
  • Posts: 634
  • Gender: Male
    • Tropico Beach
Re: MY 24 lb in action
« Reply #6 on: May 22, 2008, 09:56:17 AM »
Great photos thanks for sharing these  rampa room artillery and MR.GADGET .
By the way how much cannon grade does that powder chamber in the 12 pounder hold? And then how much does a 24 hold?
the biggest mortar I have is a beer can mortar and it can loosely fit whole in the bore of that big 24.
Logged

Offline MR.GADGET

  • Trade Count: (0)
  • Member
  • *
  • Posts: 76
  • Gender: Male
Re: MY 24 lb in action
« Reply #7 on: May 22, 2008, 10:18:54 AM »
For the most part I shoot 300 to 315 of 1f and I have some friends with 24's that shoot 700 to 900 in them. The other 4 - 12 pounders we shoot run about the same but one that shoots 240 to 260. and that's at a range for 100 yards.
Logged
MR. GADGET
NRA LIFE BENEFACTOR MEMBER
www.nra.org
Co. D, 10th Regiment N.C.S.T. "Rowan Artillery"
www.n-ssa.org

Offline rampa room artillery

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 580
Re: MY 24 lb in action
« Reply #8 on: May 22, 2008, 11:50:35 AM »
Well, with my old powder I was shooting 1100 grains to make it to 100 yards, but now i have bought a keg of really hot cannon grade so I am down to 650 for a base charge. I would be shooting 1f but i got a good deal on the cannon grade so i will use it up and buy 1f next time. hey mr gadget are you going to the artillery shoot in august? at the fort? i have never been and I am really exited to go.


rick bryan
 3rd va. co B
  ODD
  NSSA
Logged

Offline MR.GADGET

  • Trade Count: (0)
  • Member
  • *
  • Posts: 76
  • Gender: Male
Re: MY 24 lb in action
« Reply #9 on: May 22, 2008, 12:33:04 PM »
I was thinking about it If I can get a group up to shoot with.
Logged
MR. GADGET
NRA LIFE BENEFACTOR MEMBER
www.nra.org
Co. D, 10th Regiment N.C.S.T. "Rowan Artillery"
www.n-ssa.org

Offline rampa room artillery

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 580
Re: MY 24 lb in action
« Reply #10 on: May 23, 2008, 03:12:54 PM »
the carriage you see with the limber bod on it is for moving my gun around camp on it makes it easier. i am building a 5/8 scale limber now to pull it with tho, does anyone have a good line on quality/ cheap iron works for the limber box it self? maby the copper top
Logged

Offline Double D

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 12609
  • SAMCC cannon by Brooks-USA
    • South African Miniature Cannon Club
Re: MY 24 lb in action
« Reply #11 on: May 25, 2008, 06:08:44 AM »
I have plans for both the 24 PDR and 12 PDr Confederate Mortar
Logged
Pages: [1]   Go Up
« previous next »