« previous next »
Pages: [1]   Go Down

Author Topic: Choosing Base/Ring set for 1894 in 357....suggestions?  (Read 549 times)

0 Members and 1 Guest are viewing this topic.

Offline 6.5BR

  • Trade Count: (3)
  • Avid Poster
  • **
  • Posts: 207
Choosing Base/Ring set for 1894 in 357....suggestions?
« on: July 12, 2008, 08:08:17 AM »
Looking at low Talley or Warne weaver style low rings for a 4x33 scope...and undecided on 1 or 2 piece base (Warne STEEL), and if the weaver one piece is as good as any?

Steel vs Aluminum, any reason not to use a 2 piece? 

Wanting sleek rock solid mounting, w/o marring scope tube.

Thanks.
Logged

Offline dpe.ahoy

  • GBO Supporter
  • Trade Count: (7)
  • Senior Member
  • *****
  • Posts: 3363
  • Gender: Male
Re: Choosing Base/Ring set for 1894 in 357....suggestions?
« Reply #1 on: July 12, 2008, 09:25:18 AM »
IMHO the Weaver base is as good as any, and alot less $.  Can't say I would spend that much $ on either set of rings.  Even Simmons or Weaver rings can be taken off and put back on with little change in shot placement.  DP.
Logged
RIP Oct 27, 2017

Handi's:22Shot, 22LR, 2-22Mag, 22Hornet, 5-223, 2-357Max, 44 mag, 2-45LC, 7-30 Waters, 7mm-08, 280, 25-06, 30-30, 30-30AI, 444Marlin, 45-70, AND 2-38-55s, 158 Topper 22 Hornet/20ga. combo;  Levers-Marlins:Two 357's, 44 mag, 4-30-30s, RC-Glenfields 36G-30A & XLR, 3-35 Rem, M-375, 2-444P's, 444SS, 308 MX, 338Marlin MXLR, 38-55 CB, 45-70 GS, XS7 22-250 and 7mm08;  BLR's:7mm08, 358Win;  Rossi: 3-357mag, 44mag, 2-454 Casull; Winchesters: 7-30 Waters, 45Colt Trapper; Bolt actions, too many;  22's, way too many.  Who says it's an addiction?

Offline bilmac

  • GBO Supporter
  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 3560
  • Gender: Male
Re: Choosing Base/Ring set for 1894 in 357....suggestions?
« Reply #2 on: July 12, 2008, 01:30:58 PM »
Older Weaver rings would occasionally scratch your scope, but all that I have used reciently haven't been a problem. I think Weavers are just pretty good stuff and can't see why anyone would need better except high recoil situations where the scope might slip.
Logged

Offline 6.5BR

  • Trade Count: (3)
  • Avid Poster
  • **
  • Posts: 207
Re: Choosing Base/Ring set for 1894 in 357....suggestions?
« Reply #3 on: July 13, 2008, 03:53:48 AM »
Yes, my experience was with older weavers, and they would scratch upon installation if not very careful and often used tape to help.

Thanks.
Logged

Offline Icy Straits

  • Trade Count: (0)
  • Member
  • *
  • Posts: 60
Re: Choosing Base/Ring set for 1894 in 357....suggestions?
« Reply #4 on: July 16, 2008, 12:33:58 PM »
I have the two piece Warne steel with the weaver type Warne quick release style rings and they look good. I didn't like the look of the long one piece rail running past the receiver. Doesn't have much leeway for your scope mount though.
Logged
Pages: [1]   Go Up
« previous next »